739829
41
Zoom out
Zoom in
Previous page
1/44
Next page
41 GB
/ Safety system / Preparing the product for use / Cleaning and Care
Important safety instructions
· do not place any heat source, e.g. hot water
bottle or the like, on the heated overblanket
when it is switched on.
These may all damage the heated overblanket.
Do not cover the control
1
and do not lay it on
the heated overblanket when the overblanket is
in operation. The electronic components in the
control
1
cause the control
1
to heat up
slightly during operation.
Do not pull, twist or crease the cables.
These may all damage the heated overblanket.
Safety system
Note: The heated overblanket is equipped with a
safety system. Its electronic sensor technology pre-
vents the entire surface of the heated overblanket
from overheating by automatically switching off in
the event of a fault.
If the safety system switches the heated overblanket
off automatically as a result of a fault, the function
display
2
on the control
1
will no longer light up,
even when the heated overblanket is switched on.
Please note that, for safety reasons, the heated
overblanket must not be used after a fault and
must be returned to the service address indicated.
Preparing the product for use
Note: When the heated overblanket is used for the
first time, you may notice a smell of plastic; however,
this will disappear after a short time.
Before use, connect the control
1
to the heated
overblanket using the plug-in connector
3
(see Fig. B).
Switching on / off / Selecting
the temperature
Switching on:
Set the control
1
to level 1, 2, 3, 4, 5 or 6 to
switch the heated overblanket on.
Note: The function display
2
lights up after
the heated overblanket is switched on.
Switching off:
Set the control
1
to level 0 to switch the
heated overblanket off.
Note: The function display
2
goes out.
Selecting the temperature:
Just before using the heated overblanket, set it to
the highest temperature setting (level 6). This will
cause the heated overblanket to warm up quickly.
If you wish to leave the heated overblanket on for
several hours, set the lowest temperature (level 1).
Temperature levels
Set the required temperature level on the con-
trol
1
(see fig. A).
Level 0: Off
Level 1: Minimum heat
Levels 2–5: Customised heat
Level 6: Maximum heat
Automatic switch-off
Note: The heated overblanket switches itself off
automatically after approx. 180 minutes. The func-
tion display on the control
1
then starts flashing.
To switch the heated overblanket back on, first
select level 0 and after approx. 5 sec. select
the desired temperature level.
Switch the heated overblanket off (Level 0) or
pull the mains plug out of the socket if you no
longer wish to use the heated overblanket after
automatic switch-off.
Cleaning and Care
DANGER TO
LIFE BY ELECTRIC SHOCK! Be-
fore cleaning the heated overblanket,
75785_silv_Waermezudecke_Content_LB1.indd 41 30.05.12 15:46
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SWD 100 A2 IAN 75785 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SWD 100 A2 IAN 75785 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info