658895

Silvercrest SSHK 100 B2 - IAN 89479 Manual

41
Zoom out
Zoom in
Previous page
1/45
Next page
41 GB
Important safety instructions / Safety system / Preparations for use
Do not cover the control
1
and do not place it
on the heating pad when the pad is in operation.
The electronic components in the control
1
of
the heating pad cause the control
1
to heat
up slightly during operation.
Do not pull, twist or crease the cables. This
may damage the heating pad.
Safety system
Note: the heating pad is equipped with a safety
system. The electronic sensor technology prevents the
entire surface of the heating pad from overheating
by automatically switching off in the event of a fault.
If the safety system switches the heating pad off auto-
matically due to a fault, then the function display
2
on the control unit
1
is no longer illuminated, even
if the heating pad is switched on.
Please note that, for safety reasons, the heating
pad must not be used after a fault and must be
returned to the service address indicated.
Preparations for use
Note: the heating pad may smell of plastic the
first time you use it, but this will disappear after a
short period of time.
To begin, first connect the control
1
to the
heating pad with the plug-in connector
3
(see Fig. B).
Place the heating pad in position as shown in
Fig. C.
Press the two ends of the heating pad together
to allow the snap fastener
4
to snap into place.
You can use the snap fasteners
5
if you wish
a closer fit.
To remove the heating pad, release the snap
fastener
4
or the snap fasteners
5
.
Switching on / off / Selecting
the temperature
Switching on:
Set Level 1, 2, 3, 4, 5 or 6 on the control
1
to switch the heating pad on.
Note: The function display
2
illuminates
after the heating pad is switched on.
Note: Note: this heating pad features rapid
heating, which allows it to heat up within the
first 10 minutes of operation.
Switching off:
Set Level 0 on the control
1
to switch the
heating pad off.
Note: the function display
2
ceases to
illuminate.
Selecting the temperature:
Just before using the heating pad, set it to the
highest temperature setting (setting 6). This will
cause the heating pad to warm up quickly.
If you are going to use the heating pad for a
number of hours, set it to the lowest temperature
setting (setting 1).
Temperature levels
Set the required temperature level on the
control
1
(see Fig. A).
Level 0: off
Level 1: minimum heat
Level 2–5: individual heat
Level 6: maximum heat
Automatic switch-off
Note: The heating pad switches itself off auto-
matically after about 90 minutes. The function
display then starts to flash.
Then select the setting 0 and after about
5 seconds, reset the heating pad to the desired
temperature setting to switch it on again.
89479_silv_Schulterheizkissen_Content_LB1.indd 41 23.04.13 07:44
… 41 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SSHK 100 B2 - IAN 89479 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SSHK 100 B2 - IAN 89479 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info