796034

Silvercrest SOR 1500 E4 - IAN 367684 Manual

12
Zoom out
Zoom in
Previous page
1/113
Next page
GB/IE/NI/CY/MT
12
3. Before commissioning
Remove all packaging material and transport
safety devices from the appliance.
Unwind the supply cable fully from the cable
clamp
4
  
.
3.1 Assembling the rollers
Place the oil-filled radiator with its lower side
upwards on a clean, scratch-resistant base.
Attach respectively 2 rollers
3
  to
each outer recess in the retaining
plates
2
 . Use the pre-assembled
cap nuts for this purpose.
Then, position one holder
10
  respectively with the
non-threaded side in one of the two inner recesses
in the retaining plates
2
  (see Figure no. I). Now,
position the holders
10
  with rollers
3
  and retain-
ing plates
2
  on the fin (see Figures no. II + III).
Note: Observe here that the front rollers must be
attached
3
 
between the 1st and 2nd fin and the
rear rollers between the last two fins. This is the only
means to ensure correct positioning.
Both threaded fittings for the holders 10 must
finally protrude through the recesses on the
retaining
2
 
plate. Finally, fasten it in place with
a wing nut
11
 
(see Figure no. IV).
Note: Only operate the appliance with assembled
rollers
3
  and retaining plates
2
 .
3.2 Setting up the appliance
For safe, fault-free operation of the appliance, its
location must meet the following prerequisites:
The base must be firm, flat and level.
Minimum clearance from the casing of 90 cm
at the side, 90 cm at the top, 90 cm at the back
and 90 cm at the front must be adhered to.
Do not place the appliance in a hot, wet or very
wet surroundings or in the vicinity of combus-
tible material.
The mains socket must be easily accessible,
enabling easy removal of the supply cable if
necessary.
Temperature range: 0 to +40 °C
Humidity (no condensation): 5–75 %
Note: During initial use, slight odours may arise in
the short-term.
4. Commissioning
4.1 Switching the appliance on
Ensure that the heating level switch
6
  is set to
"
0
"
. Then, connect the oil-filled radiator to an
earthed socket protected by an FI circuit breaker.
Then, switch the appliance on by rotating the
temperature controller
7
clockwise until it clicks
audibly and move the heating level switch
6
to
the desired position (I, II or III). The red control
lamp
8
  is lit. Here, the following applies:
0Off position If the heating level switch
6 is in this position,
the oil-filled radiator is
switched off.
IHeating level
1:
If the heating level switch
6 is in this position,
the oil-filled radiator
provides a heat output
of 600 W.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SOR 1500 E4 - IAN 367684 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SOR 1500 E4 - IAN 367684 in the language / languages: English, German, Dutch, Danish, French, Polish, Spanish as an attachment in your email.

The manual is 3.48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info