597358

Silvercrest SNMD 33 A1 - IAN 100138 Manual

22
Zoom out
Zoom in
Previous page
1/50
Next page
22
GB / MT
Monogramming and embroidering with embroidery hoop*
Attach the embroidery and darning
plate (o)
Preparation for monogramming and
embroidering*
1. Remove the presser foot and the
presser foot holder.
2. Attach the embroidery and darning
plate (o).
3. Lower the two-step presser foot lifter
(18) before starting to sew.
4. Adjust the stitch width according to the
size of lettering or design.
1. Draw the desired lettering or design on
the rear side of the fabric.
2. Stretch the fabric between the
embroidery hoop as firmly as possible.
3. Place the fabric under the needle.
Lower the two-step presser foot lifter
(18).
4. Turn the hand wheel (21) towards you
to bring up the lower thread through
the fabric. Sew a few securing stitches
at the starting point.
5. Hold the hoop with thumb and
forefingers of both hands.
6. Coordinate the sewing speed and the
movement of hoop.
Stitch Stitch width Stitch length
B1~50
Stitch Stitch width Stitch length
B 3~5 0.5~1
Applique
1. Cut out the applique design and tack it
to the fabric.
2. Sew slowly around the edge of the
design.
3. Trim excess material outside the
stitching. Make sure not to cut any
stitches.
4. Remove the tacking thread.
5. Tie top and bottom thread under the
applique to avoid unravelling.
Sewing basics
* The embroidery hoop is not supplied with
the machine.
… 22 …


Need help? Post your question in this forum.

Forumrules
1

Forum

silvercrest-snmd-33-a1---ian-100138

Reset search

  • The cotton coming from the spool,after 2 stitches bunches up and machine stops.The handwheel is also very tight.I am new to sewing but think I have everything threaded up correctly.Thankyou Fran Submitted on 21-1-2022 at 12:47

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SNMD 33 A1 - IAN 100138 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SNMD 33 A1 - IAN 100138 in the language / languages: English, German as an attachment in your email.

The manual is 2,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info