597361

Silvercrest SNM 33 B1 - IAN 96965 Manual

78
Zoom out
Zoom in
Previous page
1/94
Next page
Place the spool (m) on the spool pin (14)
and hold it in place with a spool pin cap (r).
- Small spool pin cap for thin threads
- Large spool pin cap for thick threads
Pull the thread from the spool into the
thread guide, and up to the bobbin (2).
Pull the thread from the inside through a
hole of the empty bobbin (g). Place the
spool on the spool holder (13) and then
push to the right into the filling position.
Hold the end of the thread. Press the pedal
(t). Release the pedal (t) after a few turns.
Release the thread and cut as close as
possible to the spool. Press the pedal (t)
again.
Once the spool is full, it rotates more slowly.
Release the pedal (t). Replace the bobbin
(g) into sewing position and remove it.
If the bobbin winder spindle (13) is in the
winding position, the sewing process is
automatically interrupted. To sew, push
the bobbin winder spindle (13) to the left
(sewing position).
Note:
78
GB / IE
Inserting the bobbin
Important:
Note :
Turn power switch (19) to off ("O").
When inserting or removing the bobbin (g),
the needle must be fully raised.
1. Open the hinged cover.
2. Pull the bobbin case tab (A) and remove
the bobbin case.
3. Hold the bobbin case with one hand.
4. Insert the bobbin (3) so that the thread
runs in a clockwise direction (arrow). (4)
5. Pull the thread into the slit and under the
tension spring.
6. Hold the bobbin case between the index
finger and thumb on the bobbin case tab
(A).
7. Insert it into the shuttle race.
The method of bringing up the lower
thread is explained on page 80.
Getting ready
Winding the lower thread
1
5
6
7
A
2
3
4
A
… 78 …


Need help? Post your question in this forum.

Forumrules
1

Forum

silvercrest-snm-33-b1---ian-96965

Reset search

  • Totally lost as how to attach Two-step presser foot lifter. Do you have to attach that? Have everything else set up. HELP. It says in accessories that it is already installed. If so why is it telling me to install it? Submitted on 25-10-2020 at 19:31

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SNM 33 B1 - IAN 96965 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SNM 33 B1 - IAN 96965 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info