Manual Silvercrest SKRP 1000 A1 IAN 49029 (page 43 of 62) (English, Portuguese, Spanish)

737611

Zoom out

Zoom in

1/62

- 41 -

3. Close the battery compartment 2) by

replacing the cover and then turning the

cover with a coin to the right.

Fixing the kitchen radio beneath a

wall cabinet

With the supplied mounting plate q you can

x the kitchen radio below, for example, a

kitchen wall cabinet:

1. Determine a suitable location for the

kitchen radio.

2. Press the two retaining levers on the back

of the appliance down. Push the mounting

plate q back and remove it.

Hold the mounting plate q under the in-

stallation location. Thereby, the front edge

of the mounting plate q should be ap-

prox. 3.5 cm behind the front of the kitchen

cabinet.

4. Mark the four points for the drillholes with

a pencil.

5. Using a spike, make a small depres-

sion at the marking points. Firmly secure

the mounting plate q with the supplied

screws.

6. Hold the kitchen radio slanted, with the

two recesses in the retaining lugs on the

mounting plate q. Press the kitchen radio

upwards until it audibly engages.

Disassembly

• To disassemble the kitchen radio, press

the two retaining levers at the rear of the

appliance downwards. Then pull the ra-

dio out to the front and remove it.

• Unscrew the screws and remove the as-

sembly plate q.

Setting up the kitchen radio

Do not set the kitchen radio up without the

mounting plate q. Otherwise the speakers are

covered and the sound is scarcely audible.

To t the kitchen radio with the supplied

mounting plate q:

1. Simultaneously press the two retaining

levers on the back of the appliance down.

Push the mounting plate q back and re-

move it.

2. Push the two retainer lugs on the mount-

ing plate q into the recesses on the lower

rear side of the kitchen radio.

3. Press the mounting plate q rmly in the

direction of the appliance rear until it au-

dibly engages.

Disassembly

• Rotate the appliance with the mounting

plate to the top. Hold it in the free space

between the appliance and the mount-

ing plate.

• Lightly pull the mounting plate towards

yourself and upwards in its front area, so

as to free the plate from the front recess-

es. Remove plate from the appliance.

Providing mains power

• When you have completed installation of

the appliance, insert the plug into a mains

power socket. The display r is illuminat-

ed and the appliance tries to receive an

RDS signal to automatically adjust the

time and date.

• For as long as the appliance waits for

the RDS signal, the display r shows

"Please wait for setting thanks". This

can take several minutes.

The Settings menu

Setting the time

Should this not succeed, you must set the

clock manually. For this, the radio cannot be

switched on (= automatic mode).

In automatic mode press the button

MODE/LOCK k once. The time display

blinks.

Press the buttons UP/DOWN 1(/l

to set the time in minute intervals. Pressing

and holding the button changes the time

at ten-minute intervals.

L'allumage des diodes et de l'écran très peut visible Submitted on 21-5-2021 at 10:30
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SKRP 1000 A1 IAN 49029 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 1,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Silvercrest SKRP 1000 A1 IAN 49029

Silvercrest SKRP 1000 A1 IAN 49029 User Manual - German, Dutch, French, Italian - 54 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Silvercrest SKRP 1000 A1 IAN 49029 Manual

Product: