575446

Silvercrest SKF 2800 A1 - IAN 87713 Manual

71
Zoom out
Zoom in
Previous page
1/78
Next page
SKF 2800 A1 69
• Fat can be poured back into the cleaned
fryer, allowed to solidify and stored
together with the fryer at room
temperature.
9. Cleaning
9.1 Cleaning the appliance
To ensure your product gives you lasting
service, you should clean it regularly.
Warning! To avoid the danger of
an electric shock:
• Remove the mains plug before each
clean.
• The heating element 15 and the
casing 8 must not under any circum-
stances be cleaned under running water.
1. Press the unlock button 7 to release the lid.
The lid 4 will open.
2. Remove the frying basket 14.
3. Pull out the heating element 15 upwards.
Store the heating element 15 in a
secure, dry place.
4. Remove the fat container 13 from the
casing 8.
5. Clean the frying basket 14 and the fat
container 13 in hot water with a little
mild detergent or in a dishwasher.
6. Then rinse them with clean water and
dry them off carefully. Never use caustic
or abrasive cleaning agents or cleaning
materials such as scouring solution or
steel wool.
7. You can use a soft, damp cloth to clean
the casing 8 and the heating
element 15.
With stubborn dirt you can also use a
little mild detergent and wipe over again
with clean water.
8. Replace the fat container 13, heating
element 15 and the frying basket 14 in
the casing 8.
9. Close the lid 4.
10.Roll the mains cable up at the rear of the
casing 8.
Note You can easily transport the deep-fat
fryer using the carry handles 6 on the sides.
9.2 Remove lid and clean
The lid 4 of the deep-fat fryer can be
removed:
1. Open the lid 4
about halfway.
2. Little lugs A can be
found on the hinges
at the rear of the
appliance directly
under the springs.
Press these lugs and
pull the lid up slightly.
3. Take off the lid.
4. Clean the lid 4 with a little mild
detergent in hot water.
5. Then rinse with clean water and allow to
dry off.
6. Insert the lid back into its locators in the
casing 8.
Make sure that the hinges engage.
A
RP87713 Friteuse LB1 Seite 69 Mittwoch, 10. April 2013 2:56 14
… 71 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SKF 2800 A1 - IAN 87713 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SKF 2800 A1 - IAN 87713 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info