575410
55
Zoom out
Zoom in
Previous page
1/62
Next page
SKD 2300 A1 53
Warning! Ensure that there is
sufficient distance from the wall,
fixtures and other appliances. The
distance must be at least 1 m to
exclude the risk of fire.
1. Select a location in compliance with the
safety information (see “4. Safety
information” on page 49).
2. Plug the mains plug into a wall socket
that complies with the technical data.
Note:If you have plugged other power
consumers into the same circuit, check
that the maximum load for the installed
fuse is not exceeded, as otherwise the
fuse will trip.
5.3 Inserting the batteries
If the appliance is new or the batteries in the
remote control are flat, new type AAA/LR03
batteries must be inserted.
1. Push off the battery compartment cover
on the underside of the remote control.
2. Remove the old batteries if present.
Note: Please observe the instructions for
disposal (see “9.2 Disposable/
rechargeable batteries” on page 56).
3. Insert new batteries.
Note: Ensure the correct polarity (+/–).
The correct polarity is shown on the
bottom of the battery compartment.
4. Close the battery compartment again.
6. Operating
6.1 Using the appliance for the first
time
1. Plug the mains plug into a wall socket
that complies with the technical data (see
“3. Technical data” on page 49).
2. Switch the mains switch 9 to ON to
switch on the power supply.
The lamp in the main switch 9 lights up
and you hear a beep.
3. Press the On/Off button 22 to switch the
appliance on.
The display 5 lights up.
The appliance is now ready for use and can
be operated by means of the remote control
or control panel 2.
6.2 Selecting the temperature
Notes:
Temperature display 20:
set specified temperature
Temperature display 21:
measured actual temperature
Temperature is measured directly at the
appliance using temperature sensor 8. It
may be some time before the entire
room has also reached this temperature.
1. To choose whether you wish the
temperature to be displayed in °C or °F,
press button 24.
Selected unit of measurement 14 is
shown in the display 5.
2. Press the “Increase temperature” button 16
to increase the desired temperature up to a
maximum of 37 °C (99 °F).
Selected specified temperature 20 is
shown in display 5.
RP74308 Konvektor LB1 Seite 53 Dienstag, 26. Juni 2012 12:07 12
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SKD 2300 A1 - IAN 74308 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SKD 2300 A1 - IAN 74308 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info