575408
16
Zoom out
Zoom in
Previous page
1/76
Next page
13
SHLF 2000 B1
GB
IE
Setting the heating output
Activate the appliance by selecting the heat level. To do this, press the func-
tion selector
12
or
25
until the desired heat level is shown in the display
11
:
Low heat output: appliance produces an output of 1000 watts
High heat output: appliance produces an output of 2000 watts
To put the appliance into standby mode, press the function selector button
12
or
25
until the display
11
shows only the room temperature . After a few
seconds of overrun time, the display backlight turns off .
Selecting the temperature
Using the "Increase temperature" button
13
or
21
you can set the target tempera-
ture
to a maximum 38°C. Using the "Decrease temperature" button
14
or
23
you can set the target temperature
to a minimum 6°C.
The selected target temperature
is shown on the display
11
.
The room temperature
is measured by the temperature sensor
9
.
NOTE
As soon as the room temperature has reached the target temperature, the
heater switches off . The ventilator continues to run. If the room temperature
falls below the target temperature, the heater is reactivated automatically.
Setting the timer
The appliance has a timer that you can use to set the desired heating duration.
Once the period is over, the appliance switches off automatically.
Press the "H" button
17
or
27
to set the hours.
Press the "M" button
16
or
26
to set the minutes.
NOTE
If you keep the buttons on the appliance pressed, the values keep increasing
until you release them. The selected time is shown on the display
11
.
Swivel function
The appliance has a swivel function. This will cause the appliance to swivel back
and forth so that the warm air is more evenly distributed throughout the room.
Switch the swivel function on by pressing the button for the swivel function
18
or
22
.
Switch off the swivel function by pressing the button for the swivel function
18
or
22
again.
IB_100043_SHLF2000B1_LB3.indb 13IB_100043_SHLF2000B1_LB3.indb 13 17.06.14 15:2817.06.14 15:28
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SHLF 2000 B1 - IAN 100043 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SHLF 2000 B1 - IAN 100043 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info