740075
9
Zoom out
Zoom in
Previous page
1/45
Next page
9 GB
Important safety instructions / Safety system / Preparing the product for use
or damage. If you find such signs of damage,
if the cables are damaged or if the foot
warmer has not been used properly, it must be
returned to the manufacturer or to the service
department before it is used again. There is a
danger of electric shock and injury.
Repairs must only be carried out by specially
trained personnel or at a repair shop author-
ised by the manufacturer, since special tools
are necessary. Unsatisfactory repairs can lead
to considerable danger for the user.
Only have the foot warmer re-
paired by qualified specialist personnel using
OEM spare parts. This will ensure your foot
warmer remains safe to use.
If the mains power cable of the
foot warmer is damaged, it has to be replaced
by the manufacturer or its service department
or a similarly qualified person in order to avoid
hazards.
Safety system
Note: This foot warmer is equipped with a safety
system. The electronic sensor technology prevents
the entire surface of the foot warmer from overheat-
ing by automatically switching off in the event of a
fault. If the safety system switches the foot warmer
off automatically due to a fault, then the function
display
3
on the control unit
2
is no longer illu-
minated, even if the heating pad is switched on.
Please note that, for safety reasons, the foot
warmer must not be used after a fault and must
be returned to the service address indicated.
Preparing the product for use
Note: When the foot warmer is used for the first
time, you may notice a smell of plastic; however,
this will disappear after a short time.
Switching on / off / Selecting
the temperature
Insert the mains plug into the mains socket.
Switching on:
Set Level 1, 2, 3, 4, 5 or 6 on the control
unit
2
to switch the foot warmer on.
Note: The function display
3
illuminates
after the foot warmer is switched on.
Note: This foot warmer features rapid heating,
which allows it to heat up within the first 15
minutes of operation.
Switching off:
Set Level 0 on the control unit
2
to switch the
foot warmer off.
Note: the function display
3
ceases to illuminate.
Selecting the temperature:
Just before using the heating pad, set it to the
highest temperature setting (setting 6). This will
cause the heating pad to warm up quickly.
If you are going to use the foot warmer for a
number of hours, set it to the lowest tempera-
ture setting (setting 1).
The foot warmer can of course be used at any
time if it is switched off. Its teddy plush lining
will warm your feet even if an electric socket is
nowhere near.
Temperature levels
Set the required temperature level on the
control
2
.
Level 0: Off
Level 1: minimum heat
Level 2 - 5: Customised heat
Level 6: maximum heat
90994_silv_Fußwaermer_content_LB3 (GB-DK-BE).indd 9 29.05.13 09:50
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SFW 100 B2 IAN 90994 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SFW 100 B2 IAN 90994 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info