Manual Silvercrest SFB 10 1 A1 IAN 55975 (page 43 of 54) (English, Danish)

737647

Zoom out

Zoom in

1/54

KOMPERNASS GMBH

BURGSTRASSE 21 ⋅ D-44867 BOCHUM

www.kompernass.com

ID-Nr.: SFB 10.1 A1-10/10-V2

SFB 10.1 A1

H O M E T E C H

10-in-1 Remote Control

Operating manual

Universal fjernbetjening

Betjeningsvejledning

10-in-1 Remote Control

CV_SFB 10.1 A1 - DT-55975.indd 5 11.10.2010 10:36:11

SFB 10.1 A1

CV_SFB 10.1 A1 - DT-55975.indd 12 27.09.2010 10:34:25

- 1 -

INDEX PAGE

Important safety instructions 2

Device summary 3

Initial use 4

Unpacking the device/checking the package contents 4

Inserting the batteries 4

Operating components 5

LCD display 5

Buttons 6

SETUP - System settings 9

Code Setup (Programming the remote control) 11

Programming by brand code search 11

Programming by manual code input 12

Programming by automatic code search 12

System-Setup 14

Setting the time 14

Setting the date 14

Adjust contrast 15

Background Illumination 15

Setting the global volume/mute switching 15

Setting the lock function 16

System reset 17

Timer Setup 17

Sleep timer 17

Event timer 17

Learn Setup 18

Code learn function 19

Macro Setup 20

Favourites channel 21

Volume control 23

Vol +/—, (Mute switching) 23

For operation 23

All OFF 23

Cleaning and storage 24

Faults / Remedies 24

Disposal 25

Technical data 25

Note regarding conformity 26

Importer 26

Warranty & Service 26

BDA_SFB 10.1 A1 - DT-55975_gb.indd 1 08.10.2010 15:15:00

- 2 -

UNIVERSAL REMOTE CONTROL SFB 10.1 A1

This documentation is copyright protected. All rights includ-

ing those of photographic reproduction, duplication and

distribution by means of particular methods (for example

data processing, data carriers and data networks), wholly

or partially as well as substantive and technical changes are

reserved.

Read the operating instructions carefully before using the de-

vice for the rst time and preserve this booklet for later refer-

ence. Pass this manual on to whoever might acquire

the device at a future date.

Important safety instructions

Proper use

Children may only operate the remote control under adult

supervision.

The universal remote control can replace a maximum of ten

remote controls. It can only be used for entertainment elec-

tronics with infrared receivers. The functions of the Universal

remote control essentially correspond to those of the original

remote control. The universal remote control is intended for

private use. It is not suitable for commercial use.

Any other use is considered improper use. The manufacturer

accepts no responsibility for damage caused by improper

handling or unauthorized reconstruction.

Warning

A warning of this danger level signies a possible dangerous

situation. If the dangerous situation is not avoided it can lead

to injuries. The directives in this warning are there to avoid

personal injuries.

Important

A warning of this danger level signies possible property

damage. If the situation is not avoided it can lead to property

damage. The directives in this warning are there to avoid

property damage.

Note

A note signies additional information that assists in the

handling of the device.

Warning of injury danger as a result of

improper handling of batteries!

Batteries must be handled with special care. Take note of the

following safety instructions:

• Keep batteries well away from children. Children can

put batteries into their mouths and swallow them. If a bat-

tery is swallowed medical assistance must be sought IM-

MEDIATELY.

• Do not throw batteries into a re. Never subject batteries

to high temperatures.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 2 08.10.2010 15:15:00

- 3 -

• Explosion hazard! Non-rechargeable batteries must never

be recharged.

• Do not open the batteries or short-circuit them.

• Battery acid leaking from a battery can cause inamma-

tion of the skin. In event of contact with the skin, rinse with

large amounts of water. If the liquid comes into contact

with your eyes, rinse thoroughly with water, do not rub

and immediately consult a doctor.

Attention!

The Universal remote control contains an infrared diode

of laser class 1. In order to avoid eye injuries do not look at

the diode with optical devices.

Damage to the device

• If the device is defective, do not attempt to repair it your-

self. In case of damage, contact the manufacturer or the

manufacturer's service hotline (see Warranty information).

• If liquid escapes from the device or if the device has been

otherwise damaged, it must be inspected by the manu-

facturer or the manufacturer's service hotline. Contact the

manufacturer or the manufacturer's service hotline (see

Warranty information).

• Take the batteries out of the battery compartment as soon

as they are depleted.

• If you will not be using the device for a long period of time,

remove the batteries to prevent them from discharging.

• Always change all batteries at the same time and always

use batteries of the same type.

Device summary

q LCD display

w /ALL OFF button

e Device buttons

r S button

t Arrow buttons

y EXIT button

u P +/— buttons

i MACRO button

o Number buttons

a Button for one or two digit programme numbers

s Teletext function buttons

d Illumination button

f AV button

g Record/Playback buttons

h Mute switching

VOL +/— buttons

k MENU button

l OK button

1( FAV / EPG button

2) Infrared sender/receiver

2! Battery compartment cover

BDA_SFB 10.1 A1 - DT-55975_gb.indd 3 08.10.2010 15:15:00

- 4 -

Tips:

• The functions described here pertain to the theoretically

ideal circumstance that the button structure of the respec-

tive original remote control is identical to this universal

remote control. This only occurs, however, in rare cases. If,

therefore, not all of the original remote control's functions

can be reproduced it is not due to a diciency in the Uni-

versal remote control.

• All the brand names used in these instructions or in the

accompanying code list are trademarks of the correspond-

ing companies.

Initial use

Unpacking the device/checking the package

contents

Warning!

Keep the plastic packaging well away from small children.

There is a risk of suocation!

• Unpack the device and accessories.

• Check the package contents

- Universal remote control (URC),

- Operating instructions,

- Manufacturers directory with device code list:

- 2 x 1,5 V Batteries, type AAA/LR03 (Micro)

Note: Transport damage

If you notice any transport damage contact the manufacturer or

the manufacturer's Service-Hotline (see warranty information).

Inserting the batteries

Attention!

The Universal remote control must only be operated with

1.5 Volt batteries (Type AAA, LR03).

Carry out the battery change as quickly as possible. Preset

settings will remain saved for approx. 1 minute. If new batter-

ies have not been installed within this time all of the settings

will have to be carried out again. The time of day and date

will, however, be lost in either case.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 4 08.10.2010 15:15:00

- 5 -

1. Open the battery compartment cover 2! in the direction

of the arrow.

2. Insert the batteries as shown in the diagram and close the

battery compartment.

The LCD display q is activated as long as batteries are

installed. The following diagram shows the LCD display q

after the batteries have been installed or changed.

Note:

If no LCD display q is visible check the polarity of the

batteries or install new ones.

Operating components

LCD display

The LCD display q is divided into elds.

Text field 2@

Here is shown the currently selected device, for example

DVD, TV VCR etc.

Infrared symbol 2#

Every time a button is pressed, with which an infrared signal

is to be sent the Infrared symbol illuminates.

Code/Time field 2$

Here is shown the device code of the relevent selected de-

vice or the time of day. With the time of day indicator "

:" the

numbers blink in the middle.

Day of the week field 2%

Here you can read the English shortened form of the current

day of the week after you have entered the date.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 5 08.10.2010 15:15:00

- 6 -

MON = Monday

Tue = Tuesday

WED

= Wednesday

THU

= Thursday

FRI = Friday

SAT

= Saturday

SUN = Sunday

Standard display:

The standard readout of the LCD display q consists of the

details for the relevent device, for example, "TV", the initial

for the day of the week and the time of day indicator.

Buttons

Note:

All the functions described here can, of course, only be used

if they are supported by the device being controlled.

/ALL OFF button. w

Switch device on/o. hold down for approx.

5 seconds to switch all devices on/o.

Device buttons e

The device buttons are used to select the device that should

be operated.

Television

Video recorder

Accessory unit 1

Cable receiver

CD player

Analogue satellite receiver

Audio amplier

DVD player

Digital satellite receiver

Accessory unit 2

The mentioned button allocation is not compulsory. You can,

for example, also save the code for the video recorder on

the TV slot.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 6 08.10.2010 15:15:01

- 7 -

"S" button r

Hold down for 3 seconds to access the

SETUP menu, press brieﬂy to superimpose

the date and/or to open access to addi-

tional functions such as EPG or PIP.

Arrow buttons t

Move up, right, left and down in menus.

EXIT button y

Move a level backward in the menu.

P +/— buttons u

Change the reception channel.

MACRO button i

MACRO button i followed by a number

button o 1-6 activates a previously saved

chain of commands.

Number buttons o

Enter programme and device code numbers.

Button for one/two digit programme numbers a

For two digit programme numbers (depend-

ing on the device type) rst press

the a button then via the number buttons o

enter the programme number.

When pressed again the display becomes

single digit once more.

Teletext function buttons s

In teletext operation the buttons have the following functions:

Access the teletext function.

In normal TV operation ﬁrst press the

S button r followed by the button to

control the “PIP” function (picture in

picture) of your television set.

Stop automatic paging forward for

multi-page teletexts.

Enlarge page presentation

Screen text and TV image one upon the

other

To end the teletext function.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 7 08.10.2010 15:15:01

- 8 -

Note:

• The teletext function is only available in the European TV

mode and your TV device must have a teletext module.

• In addition the P +/- buttons u control the following

teletext functions:

P +

Leaf one page forward

P — Leaf one page backwards

Record/playback buttons f

The playback buttons f control devices such as DVD/CD

players and video recorders:

Start playback

ASPECT Image format switching with TV operation.

Record

Stop Playback/Record/Wind

Pause playback

Rewind

Wind forward

AV button g

Switch to the AV input.

Mute switching h

Switch sound on/o.

VOL+/— buttons j

Set volume (Volume).

MENU button k

Access the menu of the controlled device.

OK button l

You can conrm a menu selection with the OK

button.

FAV/EPG button 1(

Press the FAV/EPG button to access your

previously programmed favourite station.

To access the electronic programme guide

of the target device ﬁrst press brieﬂy the

S button r and then the FAV/EPG button.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 8 08.10.2010 15:15:02

- 9 -

SETUP - System settings

In the system settings you undertake the following:

• Programming the remote control to the devices to be con-

trolled

• Setting the time of day, date, display contrast, background

illumination, volume, lock function as well as system reset.

• Timer settings

• The "learning" of designated button commands

• Setting up Macros

• Assigning favourites

On the following page you can see a summary of the menu

structure.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 9 08.10.2010 15:15:02

- 10 -

BDA_SFB 10.1 A1 - DT-55975_gb.indd 10 08.10.2010 15:15:02

- 11 -

Code Setup (Programming the remote control)

3 Programming methods are available for the remote control:

Programming by brand code search, by automatic code

search and by direct code input (manual).

First you should use the brand code search since this method is

the fastest way of programming if the manufacturer of your de-

vice is itemized in the code list. As second is recommended the

direct code input followed by the automatic code search.

Programming by brand code search

With this method you select the brand and code direct via

the LCD display q.

Observe the following operational references to programme

the remote control:

Press the device button e for the device that you want to

programme the remote control.

Hold down the S button r for a little longer than 3 sec-

onds. Carry out entries in the menu quickly because after

approx. 15 seconds without an entry the menu will be

ended.

3. In the LCD display q "CODE SETUP" appears. Press the

OK button l. "ENTER CODE" now appears in the LCD

display q. With the  buttons t select "BRAND

CODE" and conrm with the OK button l.

4. Now appears the alphabetical rst brand name from the

list of pre-programmed devices.

With the 34 buttons t select the various brand names.

To make access easier you can skip directly to specic let-

ters of the alphabet with the number buttons o:

2 => A 3 => D 4 => G 5 => J

6 => M 7 => P 8 => T 9 => W

Example With button number 5 the display skips to the

letter "J". The rst brand is "JVC"*. If, for example, you

own a "Kenwood"* brand device, continue leang with

the 4 button t until this brand name appears. (* All

brand names used here are trademarks of the corre-

sponding manufacturer.)

The majority of manufacturers use several dierent codes

for the remote control. You must now ascertain which of

the available codes is best suited to your device. On the

right underneath the brand name the relevent code will

be shown in the LCD display q.

Point the remote control to the relevent device and press

the function buttons to test the code (except

34t,

OK l, EXIT y, or the number buttons o).

BDA_SFB 10.1 A1 - DT-55975_gb.indd 11 08.10.2010 15:15:02

- 12 -

9. If most of the buttons function press the OK button l to

save the setting. In the LCD display q "OK" appears.

Subsequently the menu will close automatically.

10. If, however, none or only a few of the buttons function

select with the

 or  button t the next code and test

again as described in step 8.

11.

With the EXIT button y you will move one level upwards

in the menu.

Repeat these operational steps for all devices that you would

like to control with the remote control.

Programming by manual code input

In this mode the remote control can be programmed by direct

input of a code number. You can obtain the necessary code

number from the enclosed manufacturers directory with device

code list. In the event that the new code is invalid the last valid

programmed code will be restored.

Press the device button e for the device that you want to

programme the remote control.

Hold down the S button r for a little longer than 3 sec-

onds.

In the LCD display q "CODE SETUP" appears. Press the

OK button l. "ENTER CODE" now appears in the LCD

display q. To access this function press the OK button l.

In the LCD display q appears the presently used code for

the selected device. Now the rst digit of the code blinks

and waits for your code input. Enter the new four digit

code via the number buttons o.

If the entered CODE is valid the code will be saved. In

the LCD display q "OK" appears briey. Subsequently

the menu will close automatically. In the event of failure

the LCD display q shows briey "ERROR" and waits for a

new code entry. Then you repeat step 4.

6. With the EXIT button y you will move one level upwards

in the menu.

Programming by automatic code search

This process can take several minutes per device since all

codes for the selected device have to be gone through.

Therefore this method should only be used when the device

cannot be programmed via brand code search or direct

code input or if your device is not listed at all in the manufac-

turers directory with device code list.

Follow the steps listed below to carry out programming by

means of the automatic code search.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 12 08.10.2010 15:15:02

- 13 -

1. Press the device button e for the device that is to be con-

trolled (i.e. VCR).

2. Switch the device that is to be controlled with the remote

control on. With VCR/DVD/CD devices please insert a

tape and/or disc.

Hold down the S button r for a little longer than 3 sec-

onds.

In the LCD display q "CODE SETUP" appears. Press the

OK button l. "ENTER CODE" now appears in the LCD

display q. Press the  or  button t until "SEARCH

CODE" is shown in the LCD display q. Point the remote

control to the device and then press the OK button l to

access the mode "automatic code search".

The search begins. Thereby the device sends, one after

the other, the code numbers in ascending order. The infra-

red symbol 2# indicates this.

When the device reacts by switching o press immedi-

ately the OK button l to save the relevent code. The LCD

display q shows briey "OK".

Check to see if the majority of your device's functions can

now be controlled with the remote contol. If yes you have

most probably found the correct code. In the event that a

few functions are not working you can start the automatic

code search again beginning with step 1.

Note:

However, with a renewed code search, point the URC

ﬁrst to the target device after the previously found inad-

equate code has run its course.

However if the device does not react any more you prob-

ably did not press the OK button l quick enough in step

6. Then press repeatedly the EXIT button y to exit the

menu and return to the standard display.

Now hold down the device button e of the device for

which you have just sought the relevent code. Below on

the right in the LCD display q will thereby be shown the

relevent code. Make a note of this number.

10. Then proceed as described in the preceding chapter

"Programming by manual code entry" and check to see

if the code with the next lowest number combination will

function.

Tips:

1. When code search is activated all buttons except OK l

and EXIT y are ignored.

2. If the automatic search has reached the end of the code

list it stops there. The display then returns to "SEARCH

CODE".

BDA_SFB 10.1 A1 - DT-55975_gb.indd 13 08.10.2010 15:15:02

- 14 -

System-Setup

Setting the time

The LCD display q shows you the time of day. You set this as

follows:

Hold down the S button r for a little longer than 3

seconds. The notice "CODE SETUP" appears. If appox.

15 seconds passes without an entry the device exits the

menu and returns to the standard display.

2. With the  or  button t select "SYSTEM SETUP" and

conrm with the OK button l.

In the LCD display q "TIME SETUP" appears. Conrm

with the OK button l. The LCD display q now shows

"TIME" and the time format (24 HR) blinks.

With the  or  button t you can switch to the other

time format (12 HR). After which the time display for the

time of day will show an “A” or “P” before the time. „A“

stands fpr “AM” = “ante meridium” (Morning, 0:00

o’clock midnight to 12:00 o’clock midday). „P“ stands for

“PM” = “post meridium” (Afternoon and evening, 12:00

o’clock midday to 0:00 o’clock midnight). Press the OK

button l to conrm.

Now the hour indicator blinks. With the  or  button t

select the hour number for the present time of day and

press the OK button l.

Now the minute indicator blinks. With the  or  button

t select the minute number for the present time of day

and press the OK button l to save. The "TIME SETUP"

notice appears again.

To exit this or the following menus press repeatedly the

EXIT button y until the standard display appears in the

LCD display q.

Setting the date

The LCD display q shows you the date when you press the S

button r. You set the date in this way:

Hold down the S button r for a little longer than 3 sec-

onds. The notice "CODE SETUP" appears.

With the  or  button t select "SYSTEM SETUP" and

conrm with the OK button l.

In the LCD display q "TIME SETUP" appears. Press the 

button t to change to "DATE SETUP". Conrm with the

OK button l.

In the display the year "2010" blinks. With the  or

 button t you can change the year and conrm with

the OK button l. With the  or  button t you can

change the now blinking month and conrm with the OK

button l. Now the day indicator blinks which you can

also change with the  or  button t.

To save press the OK button l. The "DATE SETUP"

notice appears again.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 14 08.10.2010 15:15:03

- 15 -

Adjust contrast

You can set the display's contrast as follows:

Hold down the S button r for a little longer than 3 sec-

onds. The notice "CODE SETUP" appears.

With the  or  button t select "SYSTEM SETUP" and

conrm with the OK button l.

With the  or  button t select "CONTRAST SETUP"

and conrm with the OK button l.

In the LCD display q the contrast value now blinks which

you can set with the  or  button t.

Display readout:

0 = highest contrast:

15 = lowest contrast

With the OK button l you can save the desired setting.

The notice "CONTRAST SETUP" appears again.

Background Illumination

You can set how long the LCD display’s q background and

the button illuminations remain alight after completion of the

operation.. Thereby taking into account that the longer the il-

lumination remains lit the shorter the battery life will be.

Hold down the S button r for a little longer than 3 sec-

onds. The notice "CODE SETUP" appears.

With the  or  button t select "SYSTEM SETUP" and

conrm with the OK button l.

With the  or  button t select "BACKLIT SETUP" and

conrm with the OK button l.

In the LCD display q now blinks the second count for the

length of time that the light is to be left on which you can

set with the   buttons t from 0 to 60. If you select

"0" the background illumination will shut o completely.

With the OK button l you can save the desired setting.

The notice "BACKLIT SETUP" appears again.

Setting the global volume/mute switching

So that you don’t always have to ﬁrst press a device button

for the volume control and mute switching, for these functions

the URC always only responds to an individual device,

by default the television set. You can determine this target

device yourself.

Hold the S button r down for a little longer than

3 seconds. The notice „CODE SETUP“ appears.

With the  or  button t select “SYSTEM SETUP” and

conﬁrm with the OK button l.

With the  or  button t select “VOL/MUTE SETUP”

and conﬁrm with the OK button l.

The LCD display q shows “ALL VOL SET”. Press the OK

button l, the display changes to „ALL VOL MODE“.

5. Now press the device button e for the device that is to be

controlled by the global volume control.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 15 08.10.2010 15:15:03

- 16 -

6. If the speciﬁed device is equipped with a volume control,

“SUCCESS” will be displayed brieﬂy and the menu will

close. From now on the volume control functions on the

device just speciﬁed.

7. If this device is not equipped with its own volume control

the URC will not allow this selection and shows “VOLUME

ERROR”. Even then the menu will close. The volume con-

trol will then continue to function on the former device.

You can also deactivate the global volume control for speciﬁc

devices.

1. For this purpose select in the VOL/MUTE SETUP with the

 or  button t the function MODE VOL SET and

conﬁrm with the OK button l.

Now press the device button e for the device that is to

be excluded from the global volume control. The LCD

display q shows „SUCCESS“ and the global volume

control is deactivated if the URC is working in the opera-

tional mode of one of the selected devices.

You can also cancel the settings again in VOL/MUTE SETUP.

1. For this purpose select in the VOL/MUTE SETUP with the

 or  button t the function VOL/MUTE RESET and

conﬁrm with the OK button l.

The LCD display q prompts you, with CONFIRM RESET,

to a conﬁrmation which is done by pressing the OK but-

ton l. Press the OK button l If you want to delete the

settings, the SUCCESS indicator then conﬁrms the dele-

tion. Otherwise you press the EXIT button y to abort the

deletion.

Note:

If you press, in this menu, the EXIT button y the entire menu

will close immediately.

Setting the lock function

With the lock function you can block access to all setup

menus.

Hold down the S button r for a little longer than 3 sec-

onds.

2. With the  or  button t select „SYSTEM SETUP“ and

conﬁrm with the OK button l.

With the  or  button t select “LOCK SETUP and

conﬁrm with the OK button l. The LCD display q shows

the current settings.

With the  or  button t now select between „LOCK“

(Block) or „UNLOCK“ (Unblock).

With the OK button l you save the setting. In the LCD

display q „LOCK SETUP“ then appears again.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 16 08.10.2010 15:15:03

- 20 -

Note:

When the LCD display shows “CONFIRM CLEAR” you can

stop the deletion with the EXIT button y.

Macro Setup

With the MACRO function up to 16 button commands can

be carried out with the press of a single button, that is to say,

several previously saved control commands can be deleted

with one MACRO button. There are 6 Macro memory slots

available for you.

To programme a Macro

For Macro programming proceed as follows:

Hold down the S button r for a little longer than 3 sec-

onds. The notice "CODE SETUP" appears.

With the  or  button t select "MACRO SETUP" and

conrm with the OK button l. In the display "MACRO

SETUP 1" appears.

With the  or  button t select the memory slot to be

programmed (MACRO SETUP 1 - 6) and conrm with the

OK button l.

4. In the LCD display q "MACRO STEP" appears. Now

press, one after the other, the desired buttons (max. 16).

The sequence should begin with a device button e.

By default the Macro commands are sent in intervals of

1 every second. Since many devices react sluggishly it is

possible that the sequence of the Macro commands are

sent too quickly to the device. Then you have the option

of programming, before a button command, a pause

of between 5 - 21 seconds. For this purpose press, if nec-

essary repeatedly, the MACRO button i. Below

and to the right the LCD display q shows the current

pause length in seconds.

When the maximum number of button commands is

reached the LCD display q shows "FULL".

Save the entry with the S button r. In the LCD display q

"MACRO SETUP" appears.

8. If, with the selection of the Macros to be programmed

(step 3), you select a memory slot that is already occupied

the existing Macro will be overwritten.

9. Repeat the process from step 3 to create further Macros.

10. With the EXIT button y you move a level upwards in the

menu except during the entry of the button commands.

Tips:

1. A maximum of 16 button commands can be saved in a

Macro. After input of the 16th button command, “FULL”

appears in the LCD display q.

2. To exit the mode without saving allow approx. 15 sec-

onds to pass without an entry.

In the mode "MACRO STEP" you can only return to the

previous status with the S button r.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 20 08.10.2010 15:15:03

- 21 -

Example: You want to save a command chain in a Macro.

We begin in the mode "MACRO STEP".

Desired command chain: Switch on TV => PAUSE => switch

to the AV input => switch on DVD => PAUSE => Playback

DVD.

In the mode "MACRO STEP", for this you enter the following

button commands:

=> => (Pause time) => => =>

=> (Pause time) =>

Execute a Macro

To execute a pre-programmed Macro proceed as follows:

Press the MACRO button i.

With the corresponding number button o you access the

desired Macro (1-6). Example: If Macro 3 is to be imple-

mented press rst the Macro button i and then, within 5

seconds, the number button "

To delete all Macros

To delete all pre-programmed Macros proceed as follows:

Hold down the S button r for a little longer than 3 sec-

onds. The notice "CODE SETUP" appears.

With the  or  button t select "MACRO SETUP" and

conrm with the OK button l. In the display "MACRO

SETUP 1" appears.

With the  or  button t select "MACRO CLEAR" and

conrm with the OK button l.

In the LCD display q "CONFIRM CLEAR" (conrm

delete) appears. Conrm the delete process with the

OK button l. The LCD display q shows "SUCCESS".

All Macros are now deleted and the menu will end.

Tips:

1. When the LCD display q shows "CONFIRM CLEAR" you

can stop the delete process with the EXIT button y.

2. Individual Macros can not be deleted they can only be

overwritten.

Favourites channel

Note:

With this function you can save your preferred stations as

favourites.

To programme favourites

Your favourite stations are saved as follows:

Press the device button e for the device that you want to

save a favourite.

Hold down the S button r for a little longer than 3 sec-

onds. The notice "CODE SETUP" appears.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 21 08.10.2010 15:15:03

- 22 -

3. With the  or  button t select "FAV CH SETUP" and

conrm with the OK button l. In the display "FAV CH

SETUP 1" appears.

With the  or  button t select the memory slot to be

programmed (FAV CH SETUP 1 - 4) and conrm with the

OK button l.

In the LCD display q "FAV CH STEP" appears. Now

press, one after the other, the buttons (max. 4) for access

to your desired favourite stations.

When the maximum number of button commands is

reached the LCD display q shows "FULL".

Save the entry with the S button r. In the LCD display q

"FAV CH SETUP" appears.

8. If, with the selection of the favourites to be programmed

(step 4), you select a memory slot that is already occu-

pied the existing favourite will be overwritten.

9. Repeat the steps to apply further favourites.

10. With the EXIT button y you move a level backwards in the

menu except during the entry of the button commands.

Note:

The input of the channel numbers can vary according to

the model and brand of the selected devices. If necessary,

with multi-digit channel numbers you must rst press the

button a.

To access favourites

To access a pre-programmed favourite press the FAV/EPG

button 1( followed by the corresponding number button for

the desired memory slot (1 - 4).

Delete All FAV channels

To delete all pre-programmed favourites proceed as follows:

Hold down the S button r for a little longer than 3 sec-

onds.

With the  or  button t select "FAV CH SETUP" and

conrm with the OK button l. In the display "FAV CH

SETUP 1" appears.

With the  or  button t select "FAV CH CLEAR" and

conrm with the OK button l.

In the LCD display q "CONFIRM CLEAR" (conrm delete)

appears. Conrm the delete process with the OK button l.

The LCD display q shows "SUCCESS". All favourites are

now deleted and the menu will end.

Tips:

1. When the LCD display q shows "CONFIRM CLEAR" you

can stop the delete process with the EXIT button y.

2. Individual favourites can not be deleted they can only be

overwritten.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 22 08.10.2010 15:15:03

- 23 -

Volume control

Vol +/—, (Mute switching)

Press the "VOL+" button to increase the volume. With the

"VOL —" button you reduce the volume. To mute the sound

press the

-button h. A further press of this button turns

the sound back on.

When you activate the VOL +/— buttons j on the URC basi-

cally the volume adjustment on the TV device is addressed,

regardless thereof, which device button e was pressed

previously. However, this does not apply to the following

devices: “AMP”, “DVD”, “ASAT”, and “DSAT” since it can

be assumed that these devices are equipped with their own

volume control.

For operation

> To operate one of the programmed devices with the URC

rst press the corresponding device button e.

Then point the URC to this device and press the desired

button.

> Put the number buttons o exactly as you do with the

original remote control. Before you make a two digit

entry press, if necessary, the

button a.

> Press the FAV/EPG button 1( to start the electronic pro-

gramme guide of a device equipped with this function.

> If you press the S button r the date is superimposed for

10 seconds in the LCD display q below and on the right.

> Whilst you hold down one of the device buttons e the

active code for this device will be superimposed below to

the right in the LCD display q.

> Via the MENU button k you access the dialogue for the

setting of the respective target device.

> Press the illumination button d to switch the display and

button illuminations on and/or off.

All OFF

Tips:

With the button ALL OFF (all o) w all devices that

are switched on can be automatically switched o. This func-

tion can switch on again devices that have already been

switched o (depending on the device). For this hold down

the ALL OFF button w for approx. 5 seconds. This will only

function under the following circumstances:

1. A visible connection exists between all the devices and

the URC.

2. Automatic code search, brand code search and MACRO

function are not active.

3. All target devices must be suitable for remote control

switch o.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 23 08.10.2010 15:15:03

- 24 -

To again switch on all devices automatically hold down once

more the button

w until all devices are switched on.

Cleaning and storage

Attention!

Ensure that moisture cannot permeate into the device

during cleaning! Otherwise there is the danger of

causing irreparable damage to the device!

> Clean the housing of the device exclusively with a soft

moist cloth and a mild dishwashing detergent.

> Store the device exclusively in an environment that com-

plies with the specications given in the technical data.

> Before storing remove the batteries so that they will not

cause damage to the device if, during storage, they

happen to leak.

Faults / Remedies

Your device does not react to the URC.

> Check the batteries. They must have enough voltage and

be properly installed.

> Firstly have you pressed the correct device button e for

the desired target device?

> Check to see that the correct code is programmed in for

the target device (see section "Code Setup").

The URC is transmitting the commands incorrectly.

> Press the corresponding device button e to set the URC

to the correct mode.

> The batteries must have enough voltage and be properly

installed.

> It is possible that you are using the wrong code. Start the

brand code search, the automatic code search or the di-

rect code input (manual).

The URC does not change the station on the device.

> Press the corresponding device button e to set the URC

to the correct mode.

> In the event that the original RC does not have a "-/- -"

button, change the programme with the P +/— buttons u or

the number buttons o.

> If this also does not work the child protection for the

target device could be activated.

Some buttons on the URC do not function properly.

> It is possible that your URC does not have all of the func-

tions that are on the device's original remote control.

> It is possible that you have not programmed in the optimal

code. Search for a code that supports more of the target

device's functions.

BDA_SFB 10.1 A1 - DT-55975_gb.indd 24 08.10.2010 15:15:03

- 25 -

The URC stops reacting after a button is pressed.

> The batteries must have enough voltage and be properly

installed.

> Point the URC towards your device.

The LCD display q shows nothing.

> The batteries must have enough voltage and be properly

installed.

> The contrast could be set too low. Increase the contrast

setting.

Disposal

Do not dispose of the device in your normal

domestic waste. This product is subject to the

European directive 2002/96/EC.

Universal remote control

• Have the universal remote control or parts of it disposed

of by a professional disposal company or by your commu-

nal disposal facility.

• Observe the currently applicable regulations. In case of

doubt contact your disposal facility.

Batteries/rechargeable batteries

• Used batteries/rechargeable batteries may not be dis-

posed of in household waste.

• Batteries can contain poisons which are damaging to the

environment. Therefore, dispose of the batteries/recharge-

able batteries in accordance with statutory regulations.

• Every consumer is legally obliged to surrender batteries/

rechargeable batteries to a community collection centre

in their district or to a dealer. The purpose of this obliga-

tion is to ensure that batteries are disposed of in a non-

polluting manner.

• Only dispose of batteries when they are fully discharged.

Dispose of packaging materials in an environmentally

responsible manner.

Technical data

Controllable devices: 10

Dimensions

L x W x H: 217 x 50 x 22 mm

Weight : 102 g (without batteries)

Infrared LED: Laser class 1

Power supply

Batteries: 2 x 1.5 V, type AAA/LR03 (micro)

(supplied)

Operating temperature: + 5 – +35°C

Storage temperature : -20 - +50 °C

Humidity: 5 - 90 % (No condensation)

BDA_SFB 10.1 A1 - DT-55975_gb.indd 25 08.10.2010 15:15:03

- 41 -

Indstilling af kontrast

Displayets kontrast kan indstilles på følgende måde:

Hold S-tasten r nede i mere end 3 sekunder. "CODE

SETUP" vises.

Med  eller  tasten t vælger du "SYSTEM SETUP"

og bekræfter derefter med OK-tasten l.

Med  eller  tasten t vælger du "CONTRAST SETUP"

og bekræfter derefter med OK-tasten l.

I LCD-displayet q blinker nu kontrastværdien, som du kan

indstille med  eller  tasten t:

Visning i displayet:

0 = højeste kontrast

15 = laveste kontrast

Med OK-tasten l gemmer du den ønskede indstilling.

"CONTRAST SETUP" vises.

Baggrundsbelysning

Du kan indstille, hvor længe LCD-displayets baggrund q og

tasterne skal blive ved med at lyse efter betjeningen. Tænk

på, at længere tid med lys reducerer batterierne levetid.

Hold S-tasten r nede i mere end 3 sekunder. "CODE

SETUP" vises.

Med  eller  tasten t vælger du "SYSTEM SETUP"

og bekræfter derefter med OK-tasten l.

Med  eller  tasten t vælger du "BACKLIT SETUP"

og bekræfter derefter med OK-tasten l.

I LCD-displayet q blinker nu sekundtallet for tiden, lyset

fortsat skal lyse, og som kan indstilles fra 0 til 60 med 

 tasterne t. Hvis du vælger "0", slukkes baggrundsbe-

lysningen helt.

Med OK-tasten l gemmer du den ønskede indstilling.

"BACKLIT SETUP" vises.

Indstilling af global lydstyrke/mute

Universalfjernbetjeningen aktiverer altid kun et enkelt appa-

rat - normalt tv-apparatet - så der ikke altid skal trykkes på en

apparattaste til lydstyrkeindstilling og muteindstilling. Dette

målapparat kan du selv bestemme.

Hold S-tasten r nede i mere end 3 sekunder. "CODE

SETUP" vises.

Med  eller  tasten t vælger du "SYSTEM SETUP"

og bekræfter derefter med OK-tasten l.

Med  eller  tasten t vælger du "VOL/MUTE SETUP"

og bekræfter derefter med OK-tasten l.

LCD-displayet q viser "ALL VOL SET". Tryk på OK-tasten l,

hvorefter displayet skifter til "ALL VOL MODE".

Tryk nu på apparattasten e til apparatet, som skal styres

af den globale lydstyrkeindstilling.

6. Hvis det angivne apparat har en lydstyrkeindstilling, vises

der kort "SUCCESS" (= succes), og menuen afsluttes. Fra

nu af virker lydstyrkeindstillingen på det valgte apparat.

BDA_SFB 10.1 A1 - DT-55975_dk.indd 41 08.10.2010 15:15:40

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SFB 10 1 A1 IAN 55975 in the language / languages: English, Danish as an attachment in your email.

The manual is 1,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Silvercrest SFB 10 1 A1 IAN 55975

Silvercrest SFB 10 1 A1 IAN 55975 User Manual - German, Dutch, French - 86 pages

Silvercrest SFB 10 1 A1 IAN 55975 User Manual - Italian, Portuguese - 86 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Silvercrest SFB 10 1 A1 IAN 55975 Manual

Product: