642279

Silvercrest SEM 1100 B3 - IAN 274989 Manual

39
Zoom out
Zoom in
Previous page
1/50
Next page
■ 36 
│
 GB
SEM 1100 B3
3) Place the sieve holder 1 in the appliance by inserting the "INSERT" mark,
which is located next to the hot water shower ., into the appliance and then
turning it clockwise until the handle of the sieve holder 1 is facing the front.
4) Place a cup under the sieve holder 1.
5) Close the steam control (turn it as far as it will go in the direction of the "-"
symbol).
6) Switch the appliance on with the on/off switch .
7) The red control lamp 0 lights up. After a short time, the pointer in the tem-
perature indicator will begin to rise.
8) As soon as the green heating-up control lamp lights up, press the "Espresso"
button
. Allow the water to flow for about 1 minute.
NOTE
► You may need to empty the cup in between. Interrupt the process by pressing
the "Espresso" button
. Empty the cup and press the "Espresso" button
again so that water flows through the appliance.
9) After about 1 minute, stop the pump by pressing the "Espresso" button
again.
10) Wait until the green heating-up control lamp lights up again.
The warming-up is concluded. You can now prepare espresso.
Heating up before every use
Before you can prepare an espresso or cappuccino, the appliance must be
heated up.
1) Switch the appliance on using the on/off switch . The red control lamp 0
lights up. Neither the "Espresso"
nor the "Steam" buttons should
be pressed in. Ensure that the steam control is turned towards "-" as far
as possible.
2) Place the sieve holder 1 in the appliance by inserting the "INSERT" mark,
which is located next to the hot water shower ., into the appliance and then
turning it clockwise until the handle of the sieve holder 1 is facing the front.
3) Press the "Espresso" button
so that the appliance draws water from
the water tank . As soon as water starts exiting the openings in the sieve
holder, press the "Espresso" button again to stop the pump.
4) Wait until the green heating-up control lamp lights up.
5) Press the "Espresso" button
again and allow hot water to flow through
for 20 seconds before stopping the pump again.
The preheating process is completed. You can now make an espresso/cappuccino.
… 39 …


Need help? Post your question in this forum.

Forumrules
1

Forum

silvercrest-sem-1100-b3---ian-274989

Reset search

  • I press the button to get coffee but the water doesn't run. What to do? Submitted on 25-2-2017 at 20:09

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SEM 1100 B3 - IAN 274989 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SEM 1100 B3 - IAN 274989 in the language / languages: English, German as an attachment in your email.

The manual is 0,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Silvercrest SEM 1100 B3 - IAN 274989

Silvercrest SEM 1100 B3 - IAN 274989 User Manual - French - 69 pages

Silvercrest SEM 1100 B3 - IAN 274989 User Manual - Italian, Portuguese, Spanish - 114 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info