679070

Silvercrest SDM 1500 C2 - IAN 280641 Manual

13
Zoom out
Zoom in
Previous page
1/76
Next page
■ 10 
│
 GB
│
IE
│
NI
SDM 1500 C2
2) If not already done: Completely unwind the power cable from the cable
hooks z/i. To facilitate the unwinding of the cable, you can fl ip down the
upper cable hook z by pulling it out a little and turning it at the same time.
3) Run the cable through the notch t on the rear of the handle so that the
cable does not hang down into the working area.
4) Insert the plug into the mains power socket.
5) Set the on/off switch u to “I”. The on/off switch u lights up, the red
POWER control lamp 0 fl ashes.
6) Use the MODE button e to select the desired level of steam generation:
– Press 1 x: low steam level, green control lamp w lights up.
– Press 2 x: high steam level, red control lamp q lights up.
– Press 3 x: no steam, standby, POWER control lamp 0 lights up.
NOTE
►
We recommend the high steam level especially for moisture- and heat-
resistant fl oor coverings, such as tiles.
► We recommend the low steam level especially for moisture- and heat-
sensitive fl oor coverings, such as parquet fl ooring.
7) Wait around 30 seconds while the appliance heats up.
8) Press the “Steam” button r. The appliance starts generating steam and,
after a short time, steam is emitted through the pad 6.
9) Wipe over the desired area.
If the water tank 8 becomes empty during use:
NOTE
►
Once the water tank 8 has been pumped empty, the pump will continue
running a little while until the empty water tank 8 is indicated by the simul-
taneous fl ashing of the red control lamp “high steam level” q, the green
control lamp “low steam level” w and POWER control lamp 0.
– Press the “Steam” button r again to stop steam production.
– Set the on/off switch u to “O”.
– Remove the water tank 8, fi ll it and replace the water tank 8 as
described in the section “Filling with water”.
– Set the on/off switch u to “I”.
– Select the desired steam level as described above and press the
“Steam” button r.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest SDM 1500 C2 - IAN 280641 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest SDM 1500 C2 - IAN 280641 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info