Manual Silvercrest PSS 65 A1 - IAN 270702 (page 11 of 100) (English, German, Dutch, Danish, Swedish, Finnish)

637276

Zoom out

Zoom in

1/100

1 1

G B I E

After switching on the device, wait until the

device has reached its max. speed. Only

then must you start with the grinding.

The disk will continue to

run after the equipment is

switched off. There is a risk

of injury.

Test run:

Before starting work and after each

change of grinding disk, carry out a test

run of at least 60 seconds with no load.

Switch off the equipment immediately if the

disk runs lumpy, substantial vibrations oc-

cur, or abnormal noises are generated.

Sharpening drills

Drills with a diameter of 3-10 mm can be

sharpened.

1. Mount the selected sharpener

(see Mounting sharpener).

2. Remove the drill holder (14) from

the sharpener.

3. Insert the drill into the drill holder

(14).

4. Insert the drill holder (14) into the

adjusting device (15).

5. Push the drill to the front into the

V-nut up to the metal stop. The

cutting edges of the drill must t

closely to the metal surfaces.

6. Using the knurled nut fasten the

drill for drill-fastening (12).

7. Remove the drill holder (14) and

insert it into the rotatable drill

mount (11).

8. Check the alignment of the drill.

The cutting edges of the drill must

be touching the grinding wheel

(10).

9. Switch the device off and grind

the drill.

10. Switch the device off and wait for

the grinding wheel (10) to stop.

11. Remove the drill holder (14)

and insert it into the rotatable

drill mount (11) by rotating in

by 180°. Using the same adjust-

ment, you can grind the opposite

cutting edge of the drill.

12. Switch the device off and grind

the drill.

13. Switch the device off and wait for

the grinding wheel (10) to stop.

Sharpening picks and chisels

1. Mount the selected sharpener

(see Mounting sharpener).

2. Place the blade on the tool table

(6) so that the end to be sharp-

ened ts closely to the edge of

the tool table (6). The magnetic

holder (5) keeps the blade in po-

sition.

3. For small picks, use the spacer

(4).

4. Select the angle according to the

existing bevel angle (angle of the

bevelled edge).

5. Release the retaining screw for

the angular adjustment (7) and

turn the tool table (6) into posi-

tion.

6. Tighten the retaining screw for

angular adjustment (7) again.

7. Switch the device on and move

the tool table (6) equally back

and forth along the grinding

wheel (10).

8. Always use light pressure while

sharpening and slowly push the

blade towards the grinding wheel

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest PSS 65 A1 - IAN 270702 in the language / languages: English, German, Dutch, Danish, Swedish, Finnish as an attachment in your email.

The manual is 2,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Silvercrest PSS 65 A1 - IAN 270702 Manual

Product: