637278
11
Zoom out
Zoom in
Previous page
1/100
Next page
11
GB IE
Grinding with the grinding
disc
Sharpening drills
Drills with a diameter of 3-10 mm can be
sharpened.
1. Mount the selected sharpener
(see Mounting sharpener).
2. Remove the drill holder (14) from
the sharpener.
3. Insert the drill into the drill holder
(14).
4. Insert the drill holder (14) into
the adjusting device (15).
5. Push the drill to the front into the
V-nut up to the metal stop. The
cutting edges of the drill must t
closely to the metal surfaces.
6. Using the knurled nut fasten the
drill for drill-fastening (12).
7. Remove the drill holder (14) and
insert it into the rotatable drill
mount (11).
8. Check the alignment of the drill.
The cutting edges of the drill
must be touching the grinding
wheel (10).
9. Switch the device off and grind
the drill.
10. Switch the device off and wait
for the grinding wheel (10) to
stop.
11. Remove the drill holder (14)
and insert it into the rotatable
drill mount (11) by rotating in
by 180°. Using the same adjust-
ment, you can grind the opposite
cutting edge of the drill.
12. Switch the device off and grind
the drill.
13. Switch the device off and wait
for the grinding wheel (10) to
stop.
Sharpening picks
and chisels
1. Mount the selected sharpener
(see Mounting sharpener).
2. Place the blade on the tool table
(6) so that the end to be sharp-
ened ts closely to the edge of
the tool table (6). The magnetic
holder (5) keeps the blade in
position.
3. For small picks, use the spacer
(4).
4. Select the angle according to the
existing bevel angle.
5. Release the retaining screw for
the angular adjustment (7) and
turn the tool table (6) into posi-
tion.
6. Tighten the retaining screw for
angular adjustment (7) again.
7. Switch the device on and move
the tool table (6) equally back
and forth along the grinding
wheel (10).
8. Always use light pressure while
sharpening and slowly push
the blade towards the grinding
wheel (10).
9. Repeat the sharpening process
until all irregularities have been
removed.
10. Switch the device off and wait
for the grinding wheel (10) to
stop.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest PSS 65 A1 - IAN 102874 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest PSS 65 A1 - IAN 102874 in the language / languages: English, German, Dutch, Danish, Swedish, Finnish as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info