470459
27
Zoom out
Zoom in
Previous page
1/55
Next page
- 25 -
Additional audio device
You can connect additional audio devices, for
example a mini disc player or a television, to the
micro system for playback over the micro system.
1. Connect the cinch plug (right channel) of the
audio device to the connection
AUX IN R.
2. Connect the cinch plug (left channel) of the
audio device to the connection
AUX IN L.
Connecting and aligning the medium
wave/wire aerial/antenna
For medium wave reception (MW) you must connect
the medium wave aerial to the micro system.
1. Unwind the connecting cable from the aerial.
2. Erect the ring until you hear it click into place in
the aerial base.
3. Push the aerial plug into the connection for the
medium wave aerial.
For VHF reception (FM) you must connect the wire
antenna to the micro system.
4. Carefully roll the wire antenna fully out, so that
the micro-system can provide good reception.
5. Insert the antenna plug of the wire antenna
into the connection socket
75 OHM JACK on the
micro system.
Note:
Should FM radio reception be inadequate,
change the position of the wire antenna.
Additional antenna via 75 ohm connection
Should FM radio reception via the supplied wire
antenna be fully inadequate, you can connect a
house antenna to the micro system.
Insert the antenna plug of the house antenna
into the connection socket
75 OHM JACK on the
micro system.
Connecting Headphones
You can connect stereo headphones to the micro-system
with a 3.5 mm jack plug. The headphone socket is
situated on the left side of the micro system. When
headphones are connected, the loudspeakers are
switched off and you will only hear sound via the
headphones.
Insert the jack plug on the headphones into the
headphone socket.
Warning:
Listening to music with headphones for
long periods and at high volume levels
can lead to hearing damage!
Power supply
When all of the required connections have been
made, insert the plug on the power cable into a
wall power socket.
Operation
Switching the device on and off in
standby mode
1. Press the button POWER.
If the time has not yet been programmed in, 00:00
is shown in the display. The micro system is now in
standby mode.
2. To switch the micro system on, press the button
STANDBY.
In the display the indicator HELLO appears and,
afterwards, the last programmed function.
3. To switch the device back into the standby
mode, press the button
STANDBY.
In the display the indicator GOOD BYE appears
and then the time.
4. To switch the device completely off, press the
button
POWER once again.
IB_KH2302_DT42354_LB5 13.01.2009 15:01 Uhr Seite 25
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest KH 2302 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest KH 2302 in the language / languages: English, Spanish as an attachment in your email.

The manual is 1,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Silvercrest KH 2302

Silvercrest KH 2302 User Manual - German, Dutch, French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info