793044

Silvercrest IAN 365240 Manual

43
Zoom out
Zoom in
Previous page
1/179
Next page
43 GB/IE
to prevent the accessory parts coming loose
from the accessory holder 10 unintentionally
during operation.
Put the accessory holder 10 back on the alu-
minium suction tube 16 after vacuuming.
Cleaning, care and
maintenance
Emptying the dust collector
To empty the dust collector 21 , it must be removed
from the main unit 4.
First remove the aluminium suction tube 16 or the
accessory part you were using (see chapter “Select-
ing, assembling and disassembling accessories”).
Proceed as follows to empty the dust collector 21 :
Switch the product off using the On / Off
button 19 (see Fig. A).
Remove the dust collector 21 from the main
unit 4 by pushing the release button 22 on
the base of the dust collector 21 (see Fig. G)
and carefully removing the dust collector 21 as
shown in figure H.
Hold the dust collector 21 over a waste bin.
The distance to the dust collector should be as
small as possible so that the dust does not un-
necessarily shake out and distribute itself in the
surrounding area.
Pull the release lever 23 downwards (towards
the user) to open the base flap 21 b on the dust
collector 21 (see Figure I).
If needed, remove hair and dust, which have
become stuck to the dust collector 21 by hand.
Close the base flap 21 b again by pushing it
back into the opening of the dust collector 21
and pushing the release lever 23 upwards
(towards the dust collector 21 ) until it audibly
clicks into place (see Fig. J).
Replace the dust collector 21 on the main unit
4 by lining up the dust collector 21 and the
cover 24 precisely in the corresponding recesses
in the main unit 4 (see Fig. K). The dust col-
lector 21 must audibly click into place, it is
only properly installed if it does so (see Fig. L).
Cleaning the filters
and dust collector
Clean the filters (HEPA filter 25
and stainless steel filter 27 ) after
every two or three uses. Other-
wise the vacuum function will be
reduced and the product could
be damaged.
Do not wash the filters (HEPA
filter 25 and stainless steel filter
27 ) in the dishwasher or wash-
ing machine.
Do not clean the HEPA filter 25
under running water.
Do not clean the dust collector
21 in the dishwasher.
Allow the stainless steel filter 27
to air dry thoroughly after clean-
ing.
Do not put the stainless steel
filter 27 in the dryer or on the
stove to dry.
IMPORTANT: Allow all parts
of the product to dry thoroughly
after cleaning. If the stainless
steel filter 27 is not fully dry, wa-
ter may seep into the product
and damage it!
To clean the filters, follow these steps:
Switch the product off using the On / Off
button 19 (see Fig. A).
Remove the aluminium suction tube 16 from
the main unit 4 by pushing the upper release
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest IAN 365240 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest IAN 365240 in the language / languages: English, German, Dutch, Danish, French, Polish, Spanish as an attachment in your email.

The manual is 5.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info