749585
19
Zoom out
Zoom in
Previous page
1/76
Next page
SABD 3.7 LI D416 GBIE
Cleaning and Care
DANGER! RISK OF ELECTRIC SHOCK!
Do not clean the appliance while charging it.
Always disconnect the battery charger w
from the mains power socket before cleaning
the appliance!
NEVER immerse the appliance in water or
any other liquid!
WARNING! RISK OF INJURY!
Ensure that the appliance is not accidentally
switched on without the dirt container 0
attached or while cleaning the rotary
brushz. Risk of injury!
ATTENTION! PROPERTY DAMAGE!
Do not use abrasive or aggressive cleaning
materials. These may damage the surfaces.
Housing
Wipe off the appliance housing with a damp
cloth. If required, use a mild washing-up liquid
on the cloth.
Ensure that the appliance is completely dry
before reconnecting it with the battery
chargerw.
Dirt container
To ensure that the performance of the cordless
sweeper does not deteriorate, empty the dirt
container 0 after every use.
Press the push-in connection q on the dirt
container 0 and pull it off.
Empty the dirt container 0 and push it back
onto the appliance so that it sits firmly on the
appliance and clicks into place on the release
knob q.
Rotary brush
If the rotary brush z can no longer be turned
because coarse dirt or threads have accumulated,
proceed as follows:
Remove the rotary brush z. Refer to figures E and
F on the fold-out page of these operation
instructions for further guidance:
1) Turn the cordless sweeper over and hold it so
that the rotary brush z is facing towards you.
2) Pull on the hook of the catch t and remove
the side cover r.
3) Pull the rotary brush z upwards out of the
housing and then out to the side.
4) Remove any dirt (on both sides of the brush
bristles) and clean the rotary brush z.
To do this, take a damp cloth and wipe the
individual bristle bundles from the inside to the
outside.
NOTE
Remove hair and threads from the brush by
cutting them with the knife e and pulling
them out of the rotary brush z.
Reinsert the rotary brush z:
1) Push the round end of the rotary brush z
onto the drive shaft u.
2) Push the square end of the rotary brush z
into the housing so that the rotary brush z
sits straight in the housing again.
3) Replace the cover r in the housing.
Make sure that the catch t engages.
IB_338593_SABD3.7LID4_LB8.indb 16 17.04.2020 14:43:34
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest IAN 338593 SABD 3.7 LI D4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest IAN 338593 SABD 3.7 LI D4 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info