739946
31
Zoom out
Zoom in
Previous page
1/46
Next page
29
GB
Disconnect the mains plug from the wall
socket…
if there is a fault,
… if you are not using the hand blender
and
during thunderstorms.
Do not use the device if there is visible
damage to the device or the power ca-
ble.
To avoid any risk, do not make modifi-
cations to the device. You also must not
replace the power cable yourself. Re-
pairs must be carried out by a specialist
workshop or the Service Centre.
DANGER! Risk of injury
from cutting
Never reach into the rotating blades. Do
not touch rotating parts with spoons or
similar utensils. Keep long hair or loose
clothing away from rotating parts as
well.
The blade continues to rotate after the
device is switched off. Wait until the
blade has come to a standstill before
you pull the hand blender out of the
food.
WARNING! Risk of material
damage
The device is designed for a maximum
operating time of 1 minute without inter-
ruption. After this, the device must re-
main switched off until it has cooled
down to room temperature.
In order to prevent damage to the de-
vice, interrupt the blending process im-
mediately if the blade is either turning
with difficulty or not turning at all. Pull
out the mains plug and check whether
there is something in the vessel blocking
movement or whether the food is too
tough. Also check whether the device is
assembled correctly.
Only use the original accessories.
Do not use any astringent or abrasive
cleaning agents.
4. Items supplied
1 Motor unit 4
1Blender 5
1 Set of operating instructions
5. Installation
Remove all packing material.
Check to ensure that all parts are pre-
sent and undamaged.
Clean the device prior to its first
use! (see “Cleaning” on page 30.)
DANGER! Risk of electric
shock! Only plug the mains plug 1
into the wall socket if the motor unit 4
has been connected to the blender 5.
Connecting the blender
(FigureA)
1. Place the motor unit 4 on the blender 5
in such a way, that the attachment mark-
ings 6 point to each other.
2. Turn the blender 5 in such a way, that
the attachment marking 6 on the
motor unit points to the lock mark-
ing 7. The motor unit 4 must engage
noticeably and audibly.
Removing the blender (Figure B)
To remove, turn the blender
5
in the op-
posite direction, so that the attachment
marking points
6 to the lock marking
7 and pull the motor unit 4 off from
the blender 5.
__RP88838_B5.book Seite 29 Montag, 4. März 2013 1:31 13
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Silvercrest H-8666 IAN 88838 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Silvercrest H-8666 IAN 88838 in the language / languages: Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Silvercrest H-8666 IAN 88838

Silvercrest H-8666 IAN 88838 User Manual - English, German, Dutch, French - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info