295114

Sigma sa 300 n Manual

38
Zoom out
Zoom in
Previous page
1/52
Next page
4. After you finish using the flash, close the flash head by pressing the
top part of the flash as shown in the illustration.
Excessive consecutive firing of the built-in flash may cause impairment
to the flash component. Do not fire the flash more than 36 times
continuously and, after a significant period of continuous firing, rest the
f
lash at east 10 minutes to allow the component to cool. Also, when you
use the flash continuously, the grip of the camera will become warm.
This is normal and not a defect.
When used with P mode
The camera will select the appropriate aperture value for any background. In bright situations, the camera will
calculate the appropriate flash amount to obtain correct exposure for both the subject and background. (Daylight
synchronization Flash)
If the subject is too bright or too dark, the aperture indicator will blink and will show limit values. If the subject is too
bright, use an ND filter to reduce the brightness. If the subject is too dark, the camera will proceed to take a flash
exposure with the aperture wide open.
When used with S mode
When you set the desired shutter speed, the camera will select the appropriate aperture value for the background. The
shutter speed will operate between 1/125 and 30 seconds. In bright situations, the camera will work the same as P
mode for Daylight synchronization Flash.
If the subject is too bright or too dark, the aperture value indicator will blink and will show limit values. If the subject
is too bright, use an ND filter to reduce the brightness. If the subject is too dark, the camera will proceed to take a
flash exposure with the aperture wide open.
If you adjust the shutter speed until the aperture value indicator stop blinking, you can get an appropriate exposure for
both the subject and background. (Slow Synchronization)
When used with A mode
When you set the desired aperture value, the camera will select the appropriate shutter speed for the background. The
shutter speed will operate between 1/125 and 30 seconds. In bright situations, the camera will work the same as P
mode for Daylight synchronization Flash.
If the subject is too bright or too dark, the shutter speed indicator will blink and will show limit values. If the subject
is too bright, use an ND filter to reduce the brightness. If the subject is too dark, set the aperture value to a wider one.
If you adjust the Aperture value until the shutter speed indicator stop blinking, you can get an appropriate exposure
for both the subject and background. (Slow Synchronization)
When used with M mode
You can set the desired shutter speed and aperture value. The shutter speed will operate between 1/125 and 30
seconds.
If you adjust exposure until the exposure meter indicates O (zero), the camera will work as for Daylight
synchronization Flash or Slow Synchronization.
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sigma sa 300 n at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sigma sa 300 n in the language / languages: English as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info