482834

Sienna SSM-4618 Manual

8
Zoom out
Zoom in
Previous page
1/10
Next page
TROUBLESHOOTING
CAUTION: Prior to cleaning or maintaining your steam mop, isolate the unit by
removing the cord from the power socket.
SOLUTION PROBLEM
LED is not on
=
Ensure steamer power cord is correctly plugged into
a 120V AC power outlet only.
=
Ensure circuit breaker is operational.
=
Try operating steamer from another power outlet.
=
If unit is still not working, call customer service at
1-888-574-3662.
No steam
=
Ensure water tank is full.
=
Calcium and mineral deposits can build up
and impact the performance of your steamer,
use distilled water if necessary.
Pale residue left on floor
=
This can be caused by leaving the steamer in the
same spot for too long. Residue can be removed
with household white vinegar or a decalcifying
product.
=
Alternatively, reheat the area for one minute to
remove residue (do not overheat area.)
Buttons are not working
properly
=
Unplug the unit from the power outlet for
5 minutes then plug back in.
Steamer is leaking water
all over the floor
=
The microfiber cloth pad may be overused and
needs to be changed out with additional cloth
pad(s) provided. Cloth pads can be cleaned in
washer/dryer. Over time, however, the cloth pads
can start to wear.
=
Be sure microfiber cloth pad is attached properly.
=
Condensation may form inside the unit dripping
water upon initial use; continue to press the steam
release button until steam appears. If necessary,
lay a towel on the floor underneath unit during
process.
=
If the unit should continue to leak water, unplug
and wait 5 minutes before trying again.
Floors are cloudy, streaky or
spotty after mopping floor
=
Be sure to use light detergent when cleaning mop
pads, any residue on pad may be transferred onto
floor.
=
Replace cloth pad with a new, clean one for
effective cleaning.
=
If initial use of steamer, past cleaning products
may have left a residue on your floor, continue to
go over effected area until there is not residue or
steaks left behind.
7
… 8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sienna SSM-4618 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sienna SSM-4618 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info