790190
31
Zoom out
Zoom in
Previous page
1/36
Next page
Faults and what to do about them en
31
3 Faults and what to do about them
Faults and what to do about them
Faults Cause/remedy
Ì on the display panel
and drying has been
interrupted.
Empty the condensate container and press the Start button ~ Page 24.
If the optional condensation drain is installed, the drain hose may be
blocked. Check the hose for deposits and flush the hose out.
¥ on the display panel. Clean the fluff filter and/or the heat exchanger, then select the Start button
~ Page 26;~ Page 29.
Dryer does not start. Mains plug plugged in or fuse checked?
program selected? Select a program.
Dryer door open? Close the door.
Childproof lock activated? Deactivate the childproof lock.
"Finish in" time selected? program starts after a delay.
Display panel goes off
and Start button flashes.
Not a fault. Energy saving mode is active ~ Page 12.
Creasing. Creasing occurs when you have exceeded the maximum load or selected
the wrong program for the type of fabric. All the required information can
be found in the program table.
Remove clothes immediately after drying; creasing may occur if they are
left in the drum.
Water is leaking out. Not a fault; the dryer may be positioned on an incline. Level the dryer.
Change in the pro-
gramme duration dis-
played during drying.
Not a fault. The moisture sensors detect the remaining moisture in the load and
adjust the programme length (except timed programmes).
Laundry is not dried cor-
rectly or is still too damp.
After the end of the program, warm laundry feels damper than it actually is.
Spread the laundry out and allow the heat to disperse.
Finely adjust the dryness level – this extends the drying time but does not
increase the temperature. Your laundry will become drier ~ Page 24.
Select a program with a longer drying time or increase the drying level. This
does not increase the temperature.
Select a timed program for subsequent drying of laundry that is still damp
~ Page 22.
Select timed program for a small load and individual items of laundry.
If you have exceeded the maximum load for the program, the laundry may
not be dried properly.
Clean the moisture sensor in the drum. The sensor may become covered by
a fine layer of limescale or residues of detergents and care products which
then impair its function. Your laundry is not being dried correctly
~ Page 30.
Drying has been interrupted as a result of a power cut, because the conden-
sate container is full or because the maximum drying time has been
exceeded.
Note: See also the laundry tips ~ Page 21.
* depending on the model
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens WT45N202GB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens WT45N202GB in the language / languages: English as an attachment in your email.

The manual is 2.77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info