790195
33
Zoom out
Zoom in
Previous page
1/56
Next page
Programme default settings en
33
0Programme default
settings
Programme default settings
You can change the default settings for
selected programmes. The settings can
be changed even while the selected
programme is running. The effects
depending on the progress of the
programme.
Temp.°C
Before and after the programme starts,
you can change the temperature
setting, depending on what stage the
programme is in, by adjusting the
desired temperature on the display.
The maximum temperature that can be
set depends on the programme that has
been selected.
Spin Speed
Depending on what stage the
programme is in, you can change the
spin speed (in rpm; revolutions per
minute) before and during the
programme by adjusting the desired
speed on the display.
setting 2: 2 =”No spin”. The rinsing
water is drained but there is no final
spin. The laundry stays wet inside the
drum, e.g. for items that should not be
spun.
You can select “No spin” to prevent
creasing if the laundry will not be taken
out of the appliance immediately after
the programme has ended.
The maximum speed that can be set
depending on the model and the
programme that has been selected.
Ready in/Time Dry
Before starting the programme, you
can preselect the programme end
("Finish in" time) in 0.5h (h = hour)
increments (between “minimum
selectable ending time” and 9.5h) or 1
hour increments (between 10h and
24h) up to a maximum of 24 hours.
To do this:
1. Select a programme (except
myTime Dry* programme).
The programme duration is
displayed for the selected
programme, e.g. 2:30
(hours:minutes).
2. Select the Ready in/Time Dry button
repeatedly until the required number
of hours is displayed.
3. Select the Start Reload button.
The programme starts.
The selected number of hours (e.g.
8h) is shown in the display panel
and counts down until the
programme starts. The duration of
the programme is then displayed.
Note: The length of the programme is
automatically adjusted when the
programme is running. Changes to the
programme default settings or
additional programme settings may also
change the programme duration.
After starting the programme (if a
“Finish in” time has been selected and
the programme has not yet started), you
can change the preselected number of
hours as follows:
1. Select the Start Reload button.
2. Select the Ready in/Time Dry button
repeatedly to change the number of
hours.
3. Select the Start Reload button.
* Depending on the model
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens WN44G290GB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens WN44G290GB in the language / languages: English as an attachment in your email.

The manual is 2.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info