710488

Siemens VSP3 Manual

38
Zoom out
Zoom in
Previous page
1/83
Next page
38
Figure
Set the adjustable floor tool:
Rugs and carpets =>
Hard floors =>
If you are vacuuming up relatively large particles, make
sure that you vacuum them up successively and
carefully to ensure that the vacuum channel of the floor
tool does not become blocked. If necessary, you should
raise the nozzle in order to better vacuum up the dirt
particles.
Figure Vacuuming with accessories
Attach the nozzles to the suction pipe or hand grip as
required:
a)Crevice nozzle for vacuuming crevices and corners,
etc.
b)Upholstery nozzle for vacuuming upholstered
furniture, curtains, etc.
Toy trap*
The toy trap can prevent small parts from being
vacuumed into the dust bag.
Figure
a)Remove the handle from the telescopic tube. Fit the
toy trap between the handle and the suction pipe.
b)Turning the wheel anti-clockwise as far as possible
activates the collection function – small parts are
retained in the collection container.
Turning the wheel clockwise deactivates the
collection function.
c)To remove the small parts that have been collected,
unlock the front window and fold it down.
● Once you have removed the small parts, close and
lock the front window (you should hear it click into
place).
● If necessary, any dirt that has collected can easily be
vacuumed off using the handle.
● Remove the toy trap after use.
!Please note:
The toy trap is not intended for continuous use and
should only be fitted when necessary.
Drill dust nozzle*
Figure
a)Secure the drill dust nozzle to the handle and then
place against the wall, so that the nozzle drill hole
opening sits directly over the hole to be drilled.
b)Select the lowest power setting and then switch on
the vacuum cleaner.
Suction holds the drill dust nozzle in the required
position.
c)Depending on the surface of the wall to be drilled it
may be necessary to readjust the power to a higher
setting to ensure the drill dust nozzle is firmly
attached.
Any fine particles are automatically vacuumed up.
13*
14*
12
15*
Figure
You can use the parking aid on the back of the vacuum
cleaner if you wish to stop vacuuming for a short time.
● Once you have switched off the appliance, slide the
hook on the floor tool into the recess on the rear of
the appliance.
Figure
To overcome obstacles, e.g. steps, the appliance can
also be carried by the handle on the appliance body.
When the work is done
Figure
a)Pull out the mains plug.
b)Briefly pull on the power cord and then release it (the
power cord retracts automatically).
Figure
To store/transport the appliance, you can use the
storage aid on the underside of the appliance.
a)Stand the appliance upright on its end.
b)Slide the hook on the floor tool into the recess on the
underside of the appliance.
Changing the filter
!
Please note: Always switch off the appliance before
changing the filter.
Replacing the dust bag
Figure
● If the dust bag change indicator in the lid is filled
completely when the floor tool is lifted from the floor
with the highest suction level selected, the dust bag
must be changed, even though it may not yet be full.
Even if the dust bag is not full, it may still need
changing, due to the type of dust which has been
vacuumed. First check that the nozzle, suction pipe
and flexible hose are not blocked, as this would also
lead to the dust bag change indicator being triggered.
● The hand grip can easily be detached from the hose
to remove blockages.
Figure Opening the lid
a)Unlock the lid by pulling on the locking lever in the
direction of the arrow.
b)Open the lid in the direction of the arrow.
Figure
a)Close the dust bag by pulling on the locking tab.
b)Take out the dust bag.
c)Insert a new dust bag.
d)Push the dust bag fully into the holder.
!
Please note: the lid will only close if a dust bag has
been inserted.
Cleaning the motor protection filter
The motor protection filter should be cleaned regularly
by knocking out the dirt and rinsing.
16
17
18
19
20*
21
22
*
depending on model
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens VSP3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens VSP3 in the language / languages: English, German, Dutch, Danish, French, Portuguese, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 5,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info