710174
73
Zoom out
Zoom in
Previous page
1/168
Next page
Cleaning and servicing en
73
Do not put any descaling tablets or
other products into the ground cof-
fee compartment.
Depending on the water hardness and
use of the appliance, the display will
show the following messages after
prior notification:
¡ "Please rinse milk system."
¡ "Descaling necessary. Please press
menu for 3 sec."
¡ "Cleaning necessary. Please press
menu for 3 sec."
¡ "calc'nClean nec. Please press
menu for 3 sec."
Notes
¡ The display indicates the progress of
the descaling or cleaning process.
¡ If your appliance is not descaled in
good time, the display will show the
following message: "Descaling over-
due. Appliance is locked. Please
press menu for 3 sec.".
¡ If your appliance has been locked,
you can only operate it again once
the descaling process has been car-
ried out.
¡ If you accidentally interrupt the ser-
vice programme, you must reset it.
→"Resetting service programmes",
Page73
Tips
¡ If you use a water filter, this prolongs
the time interval until a service pro-
grammes needs to be performed.
¡ You can combine the cleaning and
descaling programmes using the
calc'nClean service programme.
→"Using calc'nClean", Page74
¡ Clean your appliance with a soft,
damp cloth immediately after a ser-
vice programme to remove any de-
scaling solution residues and pre-
vent corrosion.
Resetting service programmes
Perform the following steps if a service
programme is interrupted, e.g. due to a
power failure.
1. Rinse out the water tank.
2. Fill the water tank with fresh, non-
carbonated water up to the "max"
marking.
3. Press ⁠.
a The appliance will rinse itself for ap-
prox.2minutes.
4. Empty and clean the drip tray.
5. Insert the drip tray and close the
door.
6. Restart the service programme.
Using the milk system cleaning
programme
Rinse the milk system with water, if ne-
cessary. The rinsing process takes ap-
prox. 1minute.
1. Press ⁠.
2. Use and to select "Cleaning
and care" and press ⁠.
3. Use and to select "Milk sys-
tem" and press ⁠.
4. To start the programme, press ⁠.
a The display will guide you through
theprogramme.
5. Place an empty glass under the out-
let system and insert the end of the
suction pipe in the glass.
6. Press ⁠.
a The milk system will now clean itself
automatically.
7. Empty the glass and clean the suc-
tion pipe.
a The program has ended and the ap-
pliance is ready for operation.
Tip:If you want to clean the milk sys-
tem particularly thoroughly, clean it reg-
ularly by hand.
→"Cleaning the milk system", Page71
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens TP507DX4 - EQ.500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens TP507DX4 - EQ.500 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 11,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens TP507DX4 - EQ.500

Siemens TP507DX4 - EQ.500 User Manual - Dutch, Polish - 252 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info