555850
13
Zoom out
Zoom in
Previous page
1/46
Next page
13/46
Siemens Heating controllers RVP201 and RVP211 CE1P2464en
Building Technologies 3 Technical design 12.12.2007
3.2 Acquisition of actual values
3.2.1 General remarks about faults in the measuring circuits
In the event of a faulty temperature sensor, the RVP201/211 always attempts to main-
tain the required comfort level in the best possible way, even if a certain amount of heat
is wasted.
In the case of serious faults that do not allow the RVP201/211 to ensure control, a fault
message will be generated. This is indicated on the controller front by the LED which
starts flashing when the current operating mode is overridden.
3.2.2 Flow or boiler temperature
Suitable are all temperature sensors that use a sensing element LG-Ni 1000 at 0 °C:
Clamp-on temperature sensor QAD22
Immersion temperature sensor QAE212…
Immersion temperature sensor QAP21.3 (complete with a ready connected cable)
If a fault occurs in the control sensor’s measuring circuit (short-circuit or interruption), the
control switches itself off (mixing valve closes or burner off, heating circuit pump on).
In any case, a fault message will be delivered; the LED on the controller front flashes.
3.2.3 Outside temperature
The following types of outside sensors can be used:
QAC22 with a sensing element LG-Ni 1000 at 0°C
QAC32 with a sensing element NTC 575 at 20°C
The controller automatically identifies the type of sensor connected.
If a fault occurs in the outside sensor’s measuring circuit, the control responds as fol-
lows:
Plants with a room temperature sensor:
The controller switches to pure room temperature control
Plants without a room temperature sensor:
The controller ensures control based on a fix outside temperature of 0 °C
A fault message is generated only when there is no actual value of the room tempera-
ture available. This is the case when no room unit is present or when the room tem-
perature measuring circuit is faulty. The LED on the controller front flashes.
3.2.4 Room temperature
The room temperature is acquired via a PPS (point-to-point interface). Only room units
that deliver suitable output signals can be connected to it.
The following types of room units can be used:
Room unit QAW50
Room unit QAW70 (room temperature sensor QAW44 can be connected in parallel)
It is also possible to connect an external switch for changeover of the current operating
mode to the PPS interface (also refer to "4 Handling"). When the switch is closed, the
room temperature cannot be measured.
Short-circuits or interruptions at the terminals do not trigger fault messages since these
statuses have a defined meaning:
Interruption = no room unit connected
Short-circuit = an external switch, if present, is activated
Types of sensors
Handling of faults
Types of sensors
Handling of faults
Types of sensors
Handling of faults
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RVP201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RVP201 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RVP201

Siemens RVP201 Installation Guide - English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info