Manual Siemens RVP201 (page 4 of 26) (English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish)

555850

Zoom out

Zoom in

1/26

Building Technologies 74 319 0614 0 c 20.05.2008 4/26

- If it flashes, the detector wiring may be faulty

- If it is lit, the controller is overridden by a remote operation

facility (room unit or changeover switch). Set room unit to

operating mode

or open the external switch)

4. Set operating mode selector to

5. Set heating curve potentiometer

to 4 and setting knob

to +8 °C:

- Flow temperature must rise: burner on, valve open, heat-

ing circuit pump on (electro-thermal actuators respond with

a certain delay!)

- If not: check wiring of the detectors (flow/boiler, outside de-

tector), actuator/burner and heating circuit pump

6. Set operating mode selector to

7. Set heating curve to 0.25 and setting knob

to –8 °C:

- Burner must switch off (observe minimum running time of

4 minutes), valve must travel toward "colder", and heating

circuit pump must remain activated

- If not: check wiring of the detectors (flow/boiler, outside de-

tector), actuator/burner and heating circuit pump

Commissioning the remote operation facility

1. Set the controller's operating mode selector to one of the two

Auto positions

2. If a room unit is present: select operating mode

on the

room unit

- Check the "Override" LED on the controller: must be lit

- If not: check wiring of the room unit

3. If a changeover switch is present: close it (gives operating

mode

on the controller).

- Check the "Override" LED on the controller: must be lit.

- If not: check wiring of the changeover switch

Commissioning of D.h.w. heating

(only RVP211)

1. The D.h.w. temperature must be around 30 °C (check by

touching or use a measuring instrument).

2. Set the controller's operating mode selector to

3. Set setting knob

to 60 °C.

- D.h.w. temperature must rise: charging pump on or

changeover valve open

- If not: check wiring of the d.h.w. temperature detector and

the heating circuit pump, or the changeover valve

4. Set setting knob

to 10 °C (observe overrun time)

- Charging pump or changeover valve must switch off

- If not: check wiring of d.h.w. temperature detector

5. Reset setting knob

to 55 °C (factory-setting).

Setting elements

Refer to figure

on page 24

1 Opening for time switch

2 LED for "Override"

3 Operating mode selector

4 Setting knob for heating curve

5 Setting knob for setback

6 Setting knob for d.h.w. temperature (only RVP211)

7 Setting knob for normal room temperature

8 Coding switches

9 Setting potentiometer for authority of room temperature

and quick setback active / inactive

10 Setting potentiometer for max. limitation of flow or boiler

temperature

11 Setting potentiometer for ECO heating limit

12 Setting potentiometer for switching differential

Coding switches

Function Switch position on the left Symbol Symbol Switch position on the right

Type of regulating unit Control of a motorized valve

Control of a atmospheric or

forced draught burner

Type of control Three-position (modulating)

Two-position (on/off)

Frost protection Yes, frost protection

No, no frost protection

D.h.w. priority (only RVP211)

With priority (absolute). Underfloor

heating systems and boiler opera-

tions: always set to abs.!

No priority (parallel)

RVP211 with boiler temperature control:

Regulating unit for d.h.w. heating Changeover valve

Charging pump

Setting potentiometers

Settings must be determined during the planning phase.

If missing, the following guide values can be used.

Potentiometer Function Setting range Guide value Notes

Switching differential

with two-position

control

1…20 K Burner control: 6 K

Authority of room

temperature on flow

temperature control

0…100 % authority

Off = quick setback is

inactive

50 % (quick setback

is active)

Plants with no room unit: setting is inactive

Plants with no outside detector:

Setting 0…100 % = quick setback is active

Setting Off = quick setback is inactive

Heating limit for ECO

automatic energy

saver

–10…+8 K (referred to

the room temperature

set value)

–3 K (gives a heat-

ing limit of 17 °C at a

room temperature

set value of 20 °C)

Off = function disabled

Max. limitation of flow

or boiler temperature

10…100 °C Guide value for un-

derfloor and ceiling

heating systems:

55 °C max.

Off = function disabled

Settings on the controller

Seal the transparent cover, if required.

Heating curve diagram: Refer to figure

on page 24

Outside temperature [°C]

1. Set heating curve as specified in the planning documen-

tation or in compliance with local practices.

2. Reset setting knob

to 0 (factory-setting, corresponds

to 20 °C room temperature).

3. Leave setting knob

to –6 °C (factory-setting).

4. Set operating mode selector to one of the two

Auto posi-

tions.

5. Set time switch as indicated in the operating instructions.

Flow temperature [°C]

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RVP201 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 0,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RVP201

Siemens RVP201 User Manual - English - 46 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens RVP201 Manual

Product: