649333
11
Zoom out
Zoom in
Previous page
1/20
Next page
Siemens Building Technologies CE1G3332xx 2015-03-06 11/20
9. Fornire tensione d'alimentazione: il LED rimane
acceso (funzionamento normale).
10. Attivare le funzioni ausiliarie (commutatore setpoint,
contatto per comando carico ecc.) se utilizzate.
11. Se si utilizza un potenziometro esterno, impostare il
cursore del potenziometro interno come segue:
sulla posizione EXT per l'impostazione del valore di
setpoint dal potenziometro esterno
sulla posizione desiderata (es. 20°C) se si utilizza
un potenziometro esterno di ritaratura (± 5K)
12. Impostare il setpoint prima sul valore minimo, poi sul
valore massimo ed osservare il funzionamento: la
risposta non deve essere né troppo veloce né troppo
lenta
Se questo non si verifica fare riferimento al par.
“Analisi guasti”
13. Impostare il setpoint sul valore richiesto.
14. Richiudere il coperchio trasparente
Regolatore con funzione limite minima
temperatura aria di mandata
1. Fornire tensione al regolatore temperatura ambiente o
di ripresa.
2. Rimuovere il coperchio.
3. Sollevare la copertura di plastica flessibile per
accedere alle impostazioni.
4. Impostare come segue:
Sequenza d'uscita: una uscita per riscaldamento
Switch n. 1 =
e switch n. 2 =
Modalità di controllo: P (switch n. 3 = e switch
n. 4 =
)
Modalità Test: Switch n. 5 =
Il valore della banda P per Y1 richiesto (ca. 25 K)
5. Richiudere la copertura flessibile.
6. Fornire tensione d'alimentazione. Il LED di
funzionamento deve lampeggiare (modalità test).
7. Impostare il setpoint di temperatura prima sul valore
minimo, poi sul valore massimo:
La richiesta del regolatore di base deve aumentare
(chiudere la valvola di raffreddamento e aprire la
valvola di riscaldamento)
Se questo non si verifica fare riferimento al par.
“Analisi guasti”
8. Togliere tensione d'alimentazione.
9. Impostare lo switch test sulla posizione normale:
switch n. 5 verso
.
10. Impostare il setpoint limite sul valore richiesto.
11. Richiudere il coperchio.
Analisi guasti
Effetto Possibile causa
La valvola non
risponde
Valvola non collegata
Manca la tensione
d'alimentazione
La valvola si posiziona
nella direzione opposta
Selezione switch 1 e 2 errati
La valvola rimane a
fine corsa
Il cursore del potenziometro a
slitta è posizionato su EXT ed il
potenziometro esterno non è
collegato
La risposta di controllo
è troppo lenta
Ridurre la banda P
In modalità PI: prima ridurre il
tempo integrale poi, se
necessario, ridurre la banda
P
Effetto Possibile causa
La regolazione è
instabile
Aumentare la banda P
In modalità PI: prima
aumentare il tempo integrale
poi, se necessario,
aumentare la banda P
pl Polski
Montaż
Miejsce montażu
Jako regulator temperatury powietrza wywiewanego:
Na kanale powietrza wywiewanego, bezpośrednio za
wylotem powietrza z pomieszczenia lub we wspólnym
kanale, jeśli jest kilka miejsc wylotu powietrza. Zawsze
przed wentylatorem powietrza wywiewanego.
Jako regulator temperatury powietrza nawiewanego:
Na kanale powietrza nawiewanego, za wentylatorem
powietrza nawiewanego, jeśli jest on zainstalowany za
ostatnim urządzeniem przygotowania powietrza, w
przeciwnym wypadku,
Na kanale powietrza nawiewanego, za ostatnim
urządzeniem przygotowania powietrza, w odległości
0,5 m.
Jako ogranicznik temperatury powietrza nawiewanego:
Na kanale powietrza nawiewanego, możliwie blisko
wlotu powietrza do pomieszczenia.
Jako regulator punktu rosy:
Tuż za osuszaczem komory zraszania.
Montaż
Procedura:
1. Najpierw należy zamocować kołnierz montażowy.
Wiercenie otworów do montażu kołnierza – patrz
„Wymiary”.
2. Ręcznie wygiąć element pomiarowy (nigdy w tym celu
nie używać narzędzi) tak, aby po zamontowaniu
przebiegał on ukośnie w poprzek kanału.
Uwaga! Element pomiarowy nie może dotykać ściany
kanału. Minimalna odległość od ściany wynosi 50 mm,
a najmniejszy promień zgięcia 10 mm.
3332Z03
3. Zamontować kołnierz montażowy.
4. Zamocować regulator na kołnierzu (wsunąć i
zatrzasnąć).
Instalacja elektryczna
Przestrzegać lokalnych przepisów dotyczących instalacji
elektrycznych.
Zaciski podłączeniowe umieszczone są pod elastyczną
pokrywą z tworzywa sztucznego.
Okablowanie wykonać zgodnie z dokumentacją
instalacji. Jeśli jest ona niedostępna, wykorzystać
schematy połączeń przedstawione w niniejszej
instrukcji.
Przestrzegać dopuszczalnych długości przewodów.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RLM162 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RLM162 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info