Manual Siemens REV33 (page 5 of 24) (English, German, Dutch, Danish, French, Italian, Polish, Spanish)

41497

Zoom out

Zoom in

1/24

CE1G2267xx 28.08.2002 5/24

On the heating engineer level, change from the flashing

CAL symbol to the volume adaption symbols by rolling

several times toward the display.

Press to accept.

(factory setting) will flash. Press

to accept or continue rolling until you reach

or .

Press to accept (also refer to Fig.

Normally sized controlled system

(factory setting):

Normal rooms, normal (steel pipe) radiators and

buildings with average insulation.

Fast controlled systems:

For small rooms, light (plate) radiators, well

insulated builgings or fan coil units.

Slow controlled systems:

For large rooms, heavy (cast iron) radiators,

poorly insulated buildings and large masses.

Control gain (adaption of heat output)

On the heating engineer level, change from the flashing

CAL symbol to the heat output adaption symbols by rolling

away from the display.

Press to accept. Symbol

(factory setting) will

flash. Press to accept or continue rolling toward the display

until you reach

or . Preess to accept (also

refer to Fig.

Normally sized heat output (standard)

Oversized heat output:

For high boiler / flow temperatures, oversized

heating surfaces or oversized volumetric flow

(nominal valve size).

Undersized heat output:

For low boiler / flow temperatures, too small

heating surfaces or too small volumetric flow

(nominal valve size).

4.2.2 Frost protection mode

Use operating mode selector to select symbol

(also refer to Fig ).

If the standard value of 5 °C need to be changed, the frost

protection setpoint

must be changed via temperature

menu T (refer to the Operating Instructions).

5. Replacing the controller

Proceed according to Fig. G.

6. Functional check

a) Check the display. If there is no display, check the

correct fitting and function of the batteries.

b) Comfort mode

c) Select temperature menu T and adjust the temperature

setpoint

to 29 °C (refer to the Operating

Instructions)

d) The controller must deliver an OPEN signal

for

about 150 seconds, and the regulating unit must run to

its limit position. If this is not the case:

• Check regulating unit and wiring

• Room temperature may be higher than 29 °C

e) Select temperature menu T and adjust the temperature

setpoint

to 5 °C (16 °C in case of set value

limitation)

f) The controller must deliver a CLOSE signal

for

about 150 seconds, and the regulating unit must run to

its limit position. If this is not the case:

• Check regulating unit and wiring

• Room temperature may be lower than 5 °C

(16 °C in the case of set value limitation)

g) Reset the setpoint temperature

to the initial value

(standard value 19 °C or individual setting)

h) Select the required operating mode

7. Reset

User-defined data:

Press the button behind the pin opening for at least one

second: this resets the user-specific settings to their

default values (the heating engineer settings will not

changed). The clock starts at 12:00. During the reset time,

all sections of the display light up, enabling them to be

checked.

All user-defined data plus the heating engineer

settings:

Press the button behind the pin opening together with the

warmer and colder buttons for at least one second.

After this reset, the factory settings will be reloaded (also

refer to section “Factory settings“).

After every reset the controller starts to an initialization

phase of 180 seconds. During this phase, the actuator is

driven to its fully closed position.

Important: The actuator reaches the fully closed position

within a maximum of 150 seconds.

After every reset the controller must be slid

back onto its base within 30 seconds.

8. Notes

• REV33 is an electric weekly programmable room

temperature controller.

• The controler conforms to “Software Class A” and is for

use in “normal” pollution situation.

• If the reference room is equipped with thermostatic

radiator valves, they must be set to their fully open

position

• The remote operation contact T1 / T2 must be wired

separately using a separate screened cable

• Ensure that the local regulations for electrical

installations are complied with

Mise en service

1. Montage

Retirer l'appareil de son socle, procédez comme indiqué

figure A.

Pour le montage, référez-vous aux figures B et C.

(voir également instructions de montage)

2. Vérifier le câblage

Les schémas de raccordement figurent au chapitre

"Schéma de raccordement". Voir aussi figures D et E.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV33 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 0,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV33

Siemens REV33 User Manual - Dutch - 2 pages

Siemens REV33 User Manual - French - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens REV33 Manual

Product: