41481

Siemens REV23 Manual

4
Zoom out
Zoom in
Previous page
1/22
Next page
4/22 28.08.2002 CE1G2264xx
d) Das Relais und somit das Stellgerät müssen spätestens
nach einer Minute schalten. Das Symbol
erscheint auf dem Display. Ist dies nicht der Fall:
• Stellgerät und Verdrahtung prüfen
• Eventuell ist die Raumtemperatur höher als 29 °C
e) Sollwerttemperatur
wieder auf den ursprünglichen
Wert zurückstellen (Standardwert 19 °C oder eigene
Einstellung)
f) Gewünschte Betriebsart wählen
7 Reset
Benutzerdefinierte Daten:
Taste hinter der Nadelöffnung mindestens eine Sekunde
drücken: Dadurch werden die benutzerspezifischen
Einstellungen auf ihre Standardwerte zurückgesetzt (die
„Fachmann“-Einstellungen bleiben unverändert). Die Uhr
beginnt bei 12:00. Während der Resetzeit leuchten alle
Anzeigefelder des Displays, und können so überprüft
werden.
Alle benutzerdefinierten Daten plus Heizfachmann -
Einstellungen:
Taste hinter der Nadelöffnung zusammen mit der Wärmer-
und Kältertaste mindestens eine Sekunde drücken.
Nach diesem Reset werden die Werkseinstellungen neu
geladen (siehe auch Abschnitt „Werkseinstellungen“ in der
Bedienungsanleitung).
8 Hinweise
• REV23 ist ein elektronischer Raumtemperaturregler mit
Wochenschaltuhr.
• Der Regler gehört zur Softwareklasse A und ist für den
Gebrauch in einer Umgebung mit normalem
Verschmutzungsgrad vorgesehen.
• Sollten im Referenzraum thermostatische
Heizkörperventile installiert sein, müssen diese
vollständig geöffnet werden
• Der Fernbedienungskontakt muss getrennt, d.h. mit
einem separaten, abgeschirmten Kabel verdrahtet
werden
• Die örtlichen Vorschriften für Elektroinstallationen sind
einzuhalten
Commissioning
1 Mounting
Remove controller from its base by proceed according to
Fig. A.
For mounting, refer to Figs. B and C and “Mounting notes“.
2 Check wiring
For the electrical connections, refer to “Connection
diagram“ (also refer to Figs. D and E).
Note: do not use stranded wires, only solid wires or
stranded wires with ferrules.
3 Remove the battery transit tab
As soon as the battery transit tab is removed, the controller
starts to operate (also refer to Fig. F).
4 Configuration
4.1 Accessing the heating engineer level
The heating engineer level will be enabled by pressing
simultaneously the warmer and colder buttons and by
rolling the roller selector away from the display and then
toward the display (also refer to Fig. H).
4.2 Functions
4.2.1 Calibrating the temperature sensor
After activating the heating engineer level, the CAL symbol
will flash. When pressing the roller selector, the room
temperature currently measured flashes and can now be
recalibrated by a maximum of ± 2 °C by rolling either
toward the display or away from it. To store the re-
calibration, press the roller selector (also refer to Fig.
).
4.2.2 Setpoint limitation
There are 2 setting choices available:
or
On the heating engineer level, change from the flashing
CAL symbol to the setpoint limitation symbol by rolling
toward the display.
Press to accept. 5...29 °C will flash (factory setting). Press
to accept or continue rolling.
Setting 16...29 °C will flash.
Press to accept.
4.2.3 Optimum start control
On the heating engineer level, change from the flashing
CAL symbol to the optimum start control symbols
by rolling twice toward the display
(also refer to Figs.
and ).
Press to accept.
will flash (factory setting).
Press to accept or continue rolling until you reach ½, 1 or
optimization OFF
. Press to accept.
4.2.4 Control mode
On the heating engineer level, change from the flashing
CAL symbol to the symbols of the various control modes
by rolling away from the display (also refer to Fig.
).
Press to accept.
(factory setting) will flash. Press
to accept (Fig. 3) or continue rolling toward the display to
select one of the following control modes:
, PID 6, PID 12 or . Press to accept the
required control mode.
A brief description of the control modes is given below
(also refer to Fig.
).
Self-learning, adaptive control:
Suited for all standard applications (factory
setting).
PID 12 Normal controlled systems:
For locations with normal temperature variations.
PID 6 Fast controlled systems:
For locations with significant temperature
variations.
Difficult controlled systems:
Proper on / off controller with a switching
differential of 0.5 C.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REV23 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV23 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV23

Siemens REV23 User Manual - English - 4 pages

Siemens REV23 User Manual - Dutch - 2 pages

Siemens REV23 User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info