465402
7
Zoom out
Zoom in
Previous page
1/40
Next page
CE1G2201xx 08.02.2008 7/40
3 Function check
a) Check the display. If there is no display, check the batteries
b) “Continuously Comfort mode“
, read the temperature
displayed
c) Set the temperature setpoint to a level above the displayed
room temperature (see operating instructions)
d) The relay and thus the actuating device must respond within 1
minute. Symbol
appears on the display. If not:
Check actuating device and wiring
The room temperature is possibly higher than the adjusted
temperature setpoint
e) Set temperature setpoint of “Continuously Comfort mode“ to
the required level
f) Select the required operating mode
4 Reset
User-defined settings:
Press simultaneously
, and for 3 seconds:
All temperature and time settings of the slider positions are reset to
their default values (refer to section “Factory settings“ in the
operating instructions). The settings made on the expert level will
remain unchanged.
The clock starts at 12:00, the date on 01-01-08
(01 – January - 2008). During the reset time, all sectors of the
display are illuminated and can thus be checked.
All user-defined settings plus those made on the expert level:
Press simultaneously the DIP switch reset button,
and
for 5 seconds:
After this reset, all factory settings will be reloaded. This applies to
both the slider settings and the settings made on the expert level.
Notes
The controller is classified as a device of software class A and
designed for use in environments with normal degree of
pollution
Indications pour le montage REV13..
1 Emplacement
Le REV13... doit être monté dans la pièce de séjour principale
(montage mural Fig. B à E).
Pour que la mesure de la température de l'air dans la pièce ne
soit pas faussée, monter l'appareil à un endroit à l'abri du
rayonnement solaire ou d'autres sources de chaleur ou de
froid.
min.
10 cm
2261Z03
2 Montage
cf. Fig. A à E
3 Vérification du câblage
Les raccordements sont indiqués dans le chapitre "Schéma de
raccordement".
Remarque: ne pas utiliser de câble plat, uniquement du
câble plein ou du câble plat avec embouts
prémontés.
4 Remarques
Respecter les prescriptions locales concernant les installations
électriques.
Si des vannes thermostatiques sont installées dans la pièce
de référence, elles doivent être ouvertes au maximum
Mise en service
1 Mise en marche du REV13..
Retirer la bande isolante noire (Figure. F); l'appareil est prêt à
fonctionner (voir aussi Mode d'emploi)
2 Sélection de la langue
Au démarrage, le type du régulateur s'affiche en haut à gauche
de l'écran, et le message de bienvenue MERCI... défile dans la
ligne de texte, dans toutes les langues disponibles
Appuyez sur une touche quelconque pour interrompre le
défilement du texte de bienvenue. La langue proposée par
défaut est "ENGLISH". Appuyer sur la touche
ou
jusqu'à ce que la langue souhaitée apparaisse. Appuyez sur
ou déplacez le curseur pour valider la langue
sélectionnée (voir aussi Fig. G).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REV13 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV13 in the language / languages: All languages as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV13

Siemens REV13 User Manual - English - 2 pages

Siemens REV13 User Manual - German - 2 pages

Siemens REV13 User Manual - Dutch - 2 pages

Siemens REV13 User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info