41493
12
Zoom out
Zoom in
Previous page
1/18
Next page
12/18 29.05.2002 CE1G2261xx
6. Működés ellenőrzés
a) Ellenőrizze a kijelzőt. Ha nincs megjelenített adat,
ellenőrizze az elemeket és polaritásukat
b) Válassza ki a folyamatos komfort
üzemmódot
c) Válassza ki a T menüt és állítsa a
hőmérsékletet
29 °C-ra (lásd a használati utasítást)
d) A relének 1 percen belül aktivizálódni kell, vagyis a
beavatkozószerv (pl.:kazán) aktivizálódik. A láng
szimbólum
megjelenik a kijelzőn. Ellenkező
esetben :
Ellenőrizze a huzalozást
A mért hőmérséklet 29 °C fölött van
e) Állíítsa vissza a
hőmérsékletet az eredeti értékre
(gyáriérték 19 °C, vagy igény szerint)
f) Válassza ki a kívánt üzemmódot
7. Gyári alapértékek visszaállítása
Végfelhasználói paraméterek :
Tartsa lenyomva legalább 1 másodpercig a ‘Reset’ gombot
a készülék hátoldalán, ezzel visszaállítja a gyári
alapértékeket (az üzembe helyezői szint beállításai nem
változnak). Az óra 12:00-ra áll vissza. A ‘Reset’ funkcióval
a kijelzőn rövid időre az összes szimbólum megjelenik.
Végfelhasználói paraméterek és üzembe helyezői
paraméterek együtt :
Tartsa lenyomva legalább 1 másodpercig a ‘Reset’ gombot
a készülék hátoldalán a ‘plusz’ és ‘mínusz’ gombokkal
együtt. Ezután a gyári beállítások állnak vissza (lásd a
“Gyári alapértékek “ fejezetet a kezelési utasításban).
8. Megjegyzések
A REV12 egy elektronikus napi programos helyiség-
hőmérséklet szabályozó
A szabályozó megfelel az “A szoftver osztálynak” és
“normál” szennyezettségű környezetnek
Amennyiben a referencia helyiség radiátorai
termosztatikus szelepekkel vannak ellátva, úgy azokat
a teljesen nyitott helyzetbe kell állítani
A huzalozásra vonatkozó helyi előírásokat figyelembe
kell venni
Uruchomienie
1. Montaż
Zdjąć regulator z podstawki i postępować zgodnie z
rysunkiem A.
Sposób montażu – patrz rysunki B i C oraz „Uwagi
montażowe”.
2. Sprawdzić okablowanie
Połączenia elektryczne – patrz: „Schemat połączeń” (oraz
rysunki D i E).
Uwaga: nie stosować plecionych przewodów, lecz
kable stałe bądź plecione z końcówkami.
3. Usunąć paski izolacyjne baterii
Po usunięciu czarnych pasków izolacyjnych z biegunów
baterii regulator rozpocznie pracę (patrz też rysunek F).
4. Konfiguracja
4.1 Dostęp do poziomu instalatora
Poziom instalatora zostanie uaktywniony po jednoczesnym
przyciśnięciu przycisków cieplej i chłodniej oraz
przekręceniu rolki nastaw w dół, a następnie w górę (patrz
też rysunek H).
4.2 Funkcje
4.2.1 Kalibracja czujnika temperatury
Przy uaktywnionionym poziomie instalatora na
wyświetlaczu miga symbol CAL. Po przyciśnięciu rolki
nastaw bieżąca zmierzona wartość temperatury w
pomieszczeniu zaczyna migać i może być wówczas
skorygowana o maksymalnie ±2 °C przez obrócenie rolki
nastaw. Po zakończeniu kalibracji, należy ponownie
przycisnąć rolkę nastaw aby zapamiętać dokonaną zmianę
(patrz też rysunek
).
4.2.2 Ograniczenie wartości zadanej
Do wyboru są dwie możliwości:
lub
Na poziomie instalatora, obrócić rolkę nastaw w górę, co
spowoduje zmianę migającego symbolu CAL na symbol
ograniczenia wartości zadanej.
Przycisnąć rolkę aby zaakceptować. Zacznie migać
5...29 °C (nastawa fabryczna). Przycisnąć rolkę aby
zaakceptować lub dalej ją obracać.
Zacznie migać nastawa 16...29 °C. Przycisnąć rolkę aby
zaakceptować (patrz też rysunek
).
4.2.3 Parametry regulacji
Na poziomie instalatora, obrócić rolkę nastaw w dół, co
spowoduje zmianę migającego symbolu CAL na symbol
parametrów regulacji (patrz też rysunek
).
Przycisnąć rolkę aby zaakceptować. Zacznie migać
(nastawa fabryczna). Przycisnąć aby
zaakceptować (rysunek 3) lub obracać ją w górę, aż do
wybrania jednego z poniższych trybów regulacji:
, PID 6, PID 12 lub . Przycisnąć rolkę aby
zaakceptować wybrany tryb regulacji.
Poniżej podano krótki opis każdego z trybów (patrz też
rysunek
).
Samouczący, regulacja adaptacyjna:
Do wszystkich standardowych zastosowań
(nastawa fabryczna).
PID 12 Normalne obiekty regulacyjne:
Do obiektów regulacyjnych z normalnymi
wahaniami temperatury.
PID 6 Szybkie obiekty regulacyjne:
Do obiektów regulacyjnych ze znacznymi
wahaniami temperatury.
Trudne obiekty regulacyjne:
regulator proporcjonalny dwustawny
z histerezą 0,5 C.
12


Need help? Post your question in this forum.

Forumrules
1

Forum

siemens-rev12

Reset search

  • I had a battery symbol appear so I changed batteries. Now the display shows every symbol there is and no matter which button I press - nothing happens. I tried the reset button and nothing happened. Help please Submitted on 5-11-2021 at 23:09

    Reply Report abuse
  • I had a battery symbol appear so I changed batteries. Now the display shows every symbol there is and no matter which button I press - nothing happens. I tried the reset button and nothing happened. Help please. Submitted on 19-10-2021 at 10:54

    Reply Report abuse
  • My heating has been off for 5 months. No display on the thermostat so replaced the batteries and reset it. Still no display at all. Help?? Submitted on 31-3-2017 at 00:36

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REV12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REV12 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REV12

Siemens REV12 User Manual - English - 3 pages

Siemens REV12 User Manual - German - 2 pages

Siemens REV12 User Manual - Dutch - 10 pages

Siemens REV12 User Manual - Dutch - 2 pages

Siemens REV12 User Manual - French - 2 pages

Siemens REV12 User Manual - Turkish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info