521719
5
Zoom out
Zoom in
Previous page
1/22
Next page
Siemens / Building Technologies / HVAC Products CE1G2217xx 24.04.2009 5/22
PID 6 Fast controlled systems:
For locations with significant temperature
variations.
Difficult controlled systems:
Proper on / off controller with a switching
differential of 0.5 C.
4.2.5 Protection mode
Use operating mode selector to select symbol (also
refer to Fig.
).
Adjustment of standard values (frost protection = 5 °C;
overheat protection = 35 °C) being done in temperature
menu T by setpoint
(refer to Operating Instructions).
5 Replacing the controller on its base
Proceed according to Fig. G.
6 Functional check
a) 60 seconds after the batteries supply power, an error
message
must appear
b) Switch on the boiler
c) The error message must disappear after 2 minutes at
the latest
d) Comfort mode
e) Select temperature menu T and adjust the temperature
setpoint
to 29 °C (refer to the Operating
Instructions)
f) The relay must be energized and thus the actuating
device activated within one minute. Flame symbol
will appear on the display. If that is not the case:
Check the boiler
The room temperature is possibly above 29 °C
g) Reset the setpoint temperature
to the initial value
(standard value 19 °C or individual setting)
h) Select the required operating mode
7 Reset
User-defined data:
Press the button behind the pin opening for at least one
second: this resets the user-specific settings and the
“Permanent-self-learning operating mode” as well as
display of flow temperature, outside temperature and
d.h.w. setpoint to their default values (the heating engineer
settings will not be changed). The clock starts at 12:00.
During the reset time, all sections of the display light up,
enabling them to be checked.
All user-defined data plus the heating engineer
settings:
Press the button behind the pin opening together with the
warmer and colder buttons for at least one second.
After this reset, the factory settings will be reloaded (also
refer to section “Factory settings“ in the operating
instructions).
Caution: If the controller is removed from its base for
more than 30 seconds, an error message will
appear on the display.
When sliding the controller back to its base,
the error message must disappear after
2 minutes at the latest.
Without inserted batteries, reset functions
correctly for a maximum of 15 seconds only
after removing REV23M from its base.
8 Notes
REA23 is an electric weekly programmable room
temperature controller.
The controller conforms to “Software Class A” and is for
use in “normal” pollution situation.
If the reference room is equipped with thermostatic
radiator valves, they must be set to their fully open
position
The remote operation contact T1 / T2 must be wired
separately using a separate screened cable
Ensure that the local regulations for electrical
installations are complied with
REA23M can only be used in connection with an
OpenTherm Plus-compatible boiler.
Mise en service
1 Montage
Retirez l'appareil de son socle, procédez comme indiqué
figure A. Pour le montage, référez-vous aux figures B et C
(voir également les instructions de montage)
2 Vérifier le câblage
Les raccordements sont indiqués dans le chapitre
"Schéma de raccordement". Voir aussi figures D et E.
Remarque : ne pas utiliser de fils tressés, uniquement des
fils ronds ou des fils avec cosses.
3 Retirer la bande isolante
Dès que la bande isolante noire est retirée du contact des
piles, l'appareil se met en marche. Voir aussi figure F.
Si l'écran reste vide, vérifier que les piles sont en place et
fonctionnent.
4 Configuration
4.1 Accès au niveau "Chauffagiste"
En appuyant simultanément sur les touches "plus chaud"
et "plus froid" et en tournant le bouton d'abord dans le sens
contraire des aiguilles d'une montre, et ensuite dans le
sens des aiguilles d'une montre, l'appareil libère l'accès au
niveau chauffagiste. Voir aussi figure H.
4.2 Fonctions diverses
4.2.1 Calibrer la sonde
Dès l'entrée au niveau Chauffagiste, le symbole CAL
clignote. En appuyant sur le bouton OK la température
actuelle clignote et peut être réajustée en tournant le
bouton de réglage de ± 2 °C max. Valider l'entrée en
appuyant sur le bouton OK (voir aussi figure
).
4.2.2 Limitation du point de consigne
2 possibilités de réglage
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REA23M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REA23M in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REA23M

Siemens REA23M User Manual - English - 2 pages

Siemens REA23M User Manual - German - 2 pages

Siemens REA23M User Manual - Dutch - 2 pages

Siemens REA23M User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info