620396
8
Zoom out
Zoom in
Previous page
1/40
Next page
8/40 24.04.2009 CE1G2218xx Siemens / Building Technologies / HVAC Products
6 Explanation to LED_1 and LED_2
LED_1 lights always in red:
LED_1 flashes in red:
LED_1 flashes 3 times in green:
LED_1 flashes 2 times in green:
LED_1 flashes 1 time in green:
LED_2 is always dark:
LED_2 lights always:
LED_2 flashes always:
LED_2 flashes briefly: Reception of control telegram
7 Finish mounting of REA-R.03/1
a) Switch off power
b) Mark location where REA-R.03/1 is currently fixed
c) If necessary loosen wiring
d) Mount receiver at location marked before according Fig. H to
M, wire completely and close housing
e) Switch on power
Commissioning the controller / transmitter REA23.03RF
1 Configuration
1.1 Accessing the heating engineer level
The heating engineer level will be enabled by pressing
simultaneously the warmer and colder buttons and by turning the
setting knob counter-clockwise and then clockwise (also refer to
Fig. G).
1.1.1 Calibrating the temperature sensor
After activating the heating engineer level, the CAL symbol will
flash. When pressing the OK-knob, the room temperature currently
measured flashes and can now be recalibrated by a maximum of ±
2 °C by turning the setting knob. To store the recalibration, press
the OK-knob (also refer to Fig.
).
1.1.2 Setpoint limitation
There are 2 setting choices available:
or
On the heating engineer level, change from the flashing CAL
symbol to the setpoint limitation symbol by turning the setting knob
clockwise (also refer to Fig.
).
Press the OK-knob to accept. 5...29 °C will flash (factory setting).
Press the OK-knob to accept or continue turning. Setting 16...29 °C
will flash.
Press the OK-knob to accept.
1.1.3 Optimum start control
On the heating engineer level, change from the flashing CAL
symbol to the optimum start control symbols
by turning the setting knob clockwise
(also refer to Figs.
and ).
Press the OK-knob to accept.
(factory setting) will
flash, optimization is switched off. Press the OK-knob to accept or
continue turning until you reach ¼ h/°C,
½ h/°C oder 1 h/°C. Press the OK-knob to accept.
1.1.4 Control mode
On the heating engineer level, change from the flashing CAL
symbol to the symbols of the various control modes by turning the
setting knob (also refer to Fig.
).
Press to accept.
(factory setting) will flash. Press the OK-knob
to accept or continue turning the setting knob to select one of the
following control modes:
, PID 6, PID 12 or . Press the OK-knob to accept the
required control mode.
A brief description of the control modes is given below (also refer to
Fig.
).
Self-learning
Adaptive control: Suited for all
standard applications.
PID 12 Normal controlled systems:
For locations with normal temperature variations.
PID 6 Fast controlled systems:
For locations with significant temperature variations.
Red on
Red off
No REA23.03RF linked
Red on
Red off
Si
g
nal stren
g
th too weak
Green on
Green off
Signal strength: Very good
1 2 3
1 2 3
Starting
sequence
Starting
sequence
Green on
Green off
Signal strength: Good
1 2
1 2
Starting
sequence
Starting
sequence
Starting
sequence
Green on
Green off
Signal strength: Satisfactory
1
1
Starting
sequence
Starting
sequence
1
Starting
sequence
Orange on
Orange off
Controlled device OFF
Orange on
Orange off
Controlled device ON
Orange on
Oran
g
e off
Learning mode active
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens REA23.03RF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens REA23.03RF in the language / languages: All languages as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens REA23.03RF

Siemens REA23.03RF User Manual - English - 2 pages

Siemens REA23.03RF User Manual - German - 2 pages

Siemens REA23.03RF User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info