555883
65
Zoom out
Zoom in
Previous page
1/82
Next page
65 / 82
Siemens RDF301, RDF301.50, RDF600KN Basic documentation CE1P3171en
Building Technologies Handling 2012-10-04
The thermostat's control parameters can be set to ensure optimum performance of
the entire system.
The parameters can be adjusted using
– Local HMI
– Synco ACS
– ETS
Commissioning of switching groups for RDF301.50 is only possible with ETS).
The control parameters of the thermostat can be set to ensure optimum
performance of the entire system (see section 3.13, control parameters).
The control sequence may need to be set via parameter P01 depending on the
application. The factory setting is as follows:
Application Factory setting P01
2-pipe and chilled / heated ceiling 1 = cooling only
4-pipe, chilled ceiling and radiator 4 = heating and cooling
When the thermostat is used with a compressor, adjust the minimum output on-
time (parameter P48) and OFF-time (parameter P49) for Y11/Y21 to avoid
damaging the compressor or shortening its life due to frequent switching
Recalibrate the temperature sensor if the room temperature displayed on the
thermostat does not match the room temperature measured (after min. 1 hour of
operation). To do this, change parameter P05
We recommend to review the setpoints and setpoint ranges (parameters
P08…P12) and change them as needed to achieve maximum comfort and save
energy
The programming mode helps identify the thermostat in the KNX network during
commissioning.
Press buttons “operating mode”
and “+” simultaneously for 6 sec to activate
programming mode, which is indicated on the display with "PrO
g
".
Programming mode remains active until thermostat identification is complete.
Use ETS to assign the KNX group addresses of the thermostat's communication
objects.
RDF301.50 has 2 switching groups with a pair of buttons each, which must be
configured via ETS. The switching groups only work in S-mode.
Each device has a unique KNX serial number inside the front panel. An additional
sticker with the same KNX serial number is enclosed in the packaging box. This
sticker is intended for installers for documentation purposes.
Control parameters
Control sequence
Compressor-based
applications
Calibrate sensor
Setpoint and range
limitation
Programming mode
Assign KNX group
addresses
Switching groups
RDF301.50 only
KNX serial number
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RDF600KN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RDF600KN in the language / languages: English as an attachment in your email.

The manual is 2,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RDF600KN

Siemens RDF600KN User Manual - German - 2 pages

Siemens RDF600KN User Manual - Dutch - 2 pages

Siemens RDF600KN User Manual - French - 2 pages

Siemens RDF600KN Installation Guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info