620368

Siemens RDD310-EH Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
CB1B1440en / 2013-09-12 Subject to change Siemens Building Technologies 2/4
Do you want to set your thermostat to Frost Protection mode?
/
Press operating mode button several times until the display shows the icon to indicate that Frost
Protection mode is selected.
The RDE410/EH has a dedicated
button to set the system either to Frost Protection mode or to switch it
on.
In Frost Protection mode
, the room temperature setpoint is maintained at 8 °C (factory setting), unless
your HVAC installer made some other setting.
Changes made by the installer Frost protection:............................ C
Do you want to change to Economy mode?
/
When Economy mode is enabled (parameter P02), press the operating mode button to select Economy
mode . In that case, the room temperature setpoint is always maintained at the Economy level. The
preset room temperature setpoint in Economy mode is 16 C (parameter P11).
The RDE410/EH has a dedicated button for selection of the desired operating mode.
Do you want to change to Auto Timer mode? (RDE410/EH only)
/
Press the
button to select Auto Timer mode . In this mode, the thermostat switches automatically
between Comfort and Economy mode according to the 8 programmed time switches.
Setting the time of day and the weekday (RDE410/EH only)
+ / –
+ / –
1. Keep the button depressed until the time digits start to flash, then press + or – to set the time of day.
If the current time format is the 24-hour format and you wish to change to the 12-hour format, keep +
depressed to pass 23:59, or keep – depressed to pass 00:00. Vice versa to go back to the 24-hour
format.
2. Confirm the time of day by pressing
. The weekday indicator starts to flash.
3. Press + or – to set the current weekday.
4. Confirm the current weekday by pressing
.
Do you want to set the time switches? (RDE410/EH only)
A..
+ / –
A..
A..
To set the time switches, keep the button depressed for 3 seconds to go to Auto Timer mode.
This mode is indicated by "Ax" appearing on the display (x = Auto Timer 1...8) and the time xx:xx flashing.
For each time switch, proceed as follows:
1. Icons
and are displayed. Press + or – to set the Comfort mode start time and confirm by
pressing .
2. Icons
and are displayed. Press + or – to set the Comfort mode end time (or Economy mode start
time) and confirm by pressing
.
3. Icon flashes. Press + or – to select or deselect each day and advance to the next day. Confirm
setting for the current time switch by pressing
and advance to the next time switch.
The thermostat exits the time switch setting mode automatically after 20 seconds if no button is pressed. All
changes made after the last press of
will not be saved!
Do you want to view the time switch settings? (RDE410/EH only)
Press the button to sequentially review all 8 programmable time switches.
Do you want to reload the default time switch settings? (RDE410/EH only)
+ / – /
Set the thermostat to Frost Protection mode
.
Press + and – simultaneously for 3 seconds. Release the buttons and, within 2 seconds, press twice the
button.
Default
settings
Day/s Time of day when controller is in Comfort mode
Mo (1) – Fr (5) 06:30 – 08:30 (A1) 17:30 – 22:30 (A2)
Sa (6) 08:00 – 23:00 (A3)
Su (7) 08:00 – 22:30 (A4)
– During the remaining time, the RDE410/EH operates in Economy mode
– Time switches A5…A8 have no default settings
Commissioning (by qualified HVAC installer)
To adapt the thermostat to your system and to optimize the control performance, a number of control parameters can be set.
This can also be made during operation without opening the thermostat.
3/4 CB1B1440en / 2013-09-12 Subject to change Siemens Building Technologies
Recalibrating the temperature sensor
If the room temperature displayed by the thermostat does not accord with the temperature effectively
measured, the temperature sensor can be recalibrated. Using parameter P05, the temperature can be
adjusted by pressing + or – in increments of 0.5 °C. The maximum recalibration range is +/- 3 °C.
Economy mode
If you want to change the factory-set temperature setpoint (16 °C for heating), readjust parameter P11.
Caution: The setpoint for Economy mode can be set to "Off". This means that the thermostat will be
deactivated! This means that there will be no protective heating function, therefore risk of frost!
Electrical floor heating/cable temperature sensor (floor sensor)
The factory setting for this function is "Off" and must be set to "On" if electrical floor heating is used. This
function is activated via parameter P38.
The installer must select the approximate capacity of the heating system (in kW) via parameter P45 during
commissioning.
The cable temperature sensor is connected to input X1, M and acquires the floor temperature. If the floor
temperature exceeds the parameterized
limit xx ºC (P38 = 1, P51 = xx ºC), the heating system is turned off
until the floor temperature returns to a level below the parameterized limit. A typical application are rooms (dry
floor).
If the application does not require floor temperature limitation but instead uses the external sensor for room
temperature display and control, the parameters have to be set as follows: P38 = 1, P51 = Off. A typical
application are bathrooms (wet floor) where a constant floor temperature is required
It is not recommended to have only a built-in room sensor for floor heating since in that case there is a risk of
overheating.
Energy saving tips without loss of comfort:
Never allow room temperatures to exceed 21 °C
When absent, set the thermostat to Economy mode (or Frost Protection), even for short periods of time
Air out the rooms briefly, but with windows wide open
2


Need help? Post your question in this forum.

Forumrules
1

Forum

siemens-rdd310-eh

Reset search

  • hello,when i turn it on it lowers my room temp by 6 degrees,why?
    Submitted on 2-2-2018 at 21:44

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RDD310-EH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RDD310-EH in the language / languages: English as an attachment in your email.

The manual is 0,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RDD310-EH

Siemens RDD310-EH User Manual - German - 2 pages

Siemens RDD310-EH User Manual - Dutch - 2 pages

Siemens RDD310-EH User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info