620391

Siemens RCR10-868 Manual

10
Zoom out
Zoom in
Previous page
1/56
Next page
10/56 2015-03-18 CE1G2206xx
The expert level is quit by pressing the operating mode selection button .
Code list
Function block Code Name Factory setting Your setting
Basic settings
00 Language English
01 Sensor calibration off
02 Switching differential 0.5 °C
LCD settings
10 Illumination time 10 seconds
11 Background brightness 0
12 Contrast 0
Clock settings
30
Time zone
Deviation from time signal received from Frankfurt
(Central European Time CET) (refer to Note 1)
0 hours
31 Start of summer time (refer to Note 2) March 31 (31-03)
32 End of summer time (refer to Note 3) October 31 (31-10)
Note 1: If the radio clock is not active or not present, this setting has no impact.
With the radio clock active, the time signal received from Frankfurt is shifted by the value set under code 30 (time zone).
Note 2: If the radio clock is not active or not present, the time change always takes place at 02:00 on the Sunday before the set date.
With the radio clock active, the time change is shifted by the value set under code 30 (time zone).
Note 3: If the radio clock is not active or not present, the time change always takes place at 03:00 on the Sunday before the set date.
With the radio clock active, the time change is shifted by the value set under code 30 (time zone).
3 Function check
a) Check the display. If there is no display, check the batteries
b) “Continuously Comfort mode“
, read the temperature displayed
c) REV.. in heating mode: Set the temperature setpoint to a level above the
displayed room temperature (see operating instructions).
REV.. in cooling mode: Set the temperature setpoint to a level below the
displayed room temperature (see operating instructions).
d) The relay and thus the actuating device must respond within
1 minute. Symbol ▲ appears on the display. If not:
· Check actuating device and wiring
· In heating mode, the room temperature is possibly higher than the
adjusted temperature setpoint, in cooling mode possibly lower
e) Set temperature setpoint of “Continuously Comfort mode“ to the
required level
f) Select the required operating mode
4 Reset
User-defined settings:
Press simultaneously
, and for 3 seconds:
All temperature and time settings of the slider positions are reset to their default
values (refer to section “Factory settings“ in the operating instructions). The
settings made on the expert level will remain unchanged.
The clock starts at 12:00, the date on 01-01-08
(01 - January - 2008). During the reset time, all sectors of the display are
illuminated and can thus be checked.
All user-defined settings plus those made on the expert level:
Press simultaneously the DIP switch reset button, and for 5
seconds:
After this reset, all factory settings will be reloaded. This applies to both the
slider settings and the settings made on the expert level.
Notes
· The controller is classified as a device of software class A and designed
for use in environments with normal degree of pollution
· REV24RF/SET is a set of units consisting of electronic room temperature
controller with 7-day time switch, RF transmitter (REV24RF..) and RF
receiver (RCR10/868)
DE
EN
FR
IT
NL
ES
PT
CS
HU
PL
SV
FI
DA
TR
EL
RO
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens RCR10-868 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens RCR10-868 in the language / languages: All languages as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens RCR10-868

Siemens RCR10-868 User Manual - English - 2 pages

Siemens RCR10-868 User Manual - German - 2 pages

Siemens RCR10-868 User Manual - French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info