680392

Siemens OpenScape DECT Phone S5 on OpenScape Cordless Enterprise Manual

35
Zoom out
Zoom in
Previous page
1/85
Next page
34 Questions and answers
Questions and answers
Manufacturer's advice
Authorization
Depending on the variant, this device is intended for analog phone lines in the German/Luxembourg or
Austrian network (see device label).
Country-specific requirements have been taken into consideration.
We, Unify Software and Solutions GmbH & Co. KG, declare that this device meets the essential requirements and other relevant
regulations laid down in Directive 1999/5/EC.
The EU declaration of conformity for your country under 1999/5/EC can be found at:
wiki.unify.com/wiki/Declarations_of_Conformity#Cordless_Phones.
This declaration may also be available in the files "International Declarations of Conformity" or "European
Declarations of Conformity" in some cases.
Therefore please also read these files.
The display is blank.
• The handset is not switched on. Press and hold
• The battery is empty. Charge the battery or replace it ( p. 8)
"No Base" flashes on the display.
• The handset is outside the range of the base. Reduce the distance between the handset and base
"Please register handset" flashes on the display.
• The handset is not yet registered or was de-registered when another handset was registered.
Register the handset again
The handset does not ring.
• The ringtone is deactivated. Activate the ringtone ( p. 31)
• The phone does not ring during a specific period or for certain numbers.
¤ Check the time control for external calls ( p. 21)
The other party cannot hear you.
• The handset is "muted". Reactivate the microphone ( p. 14)
The caller's number is not displayed.
• Calling Line Identification (CLI) is not enabled for the caller. The caller should ask the network
provider to enable Calling Line Identification(CLI).
• Calling Line Identification Presentation (CLIP) is not supported or enabled by the network provider.
Ask the network provider to enable Calling Line Identification Presentation (CLIP).
• The phone is connected via a PABX or a router with an integrated PABX (gateway) that does not forward
all information.
¤ Reset the system: Pull out the power plug briefly. Reinsert the plug and wait until the device restarts.
¤ Check the settings on the PABX and activate phone number display if necessary. To do this, search
for terms such as CLIP, calling line identification, telephone number identification, caller ID, ... in the
system user guide or ask the system manufacturer.
You hear an error tone when keying in (descending tone sequence).
• Action has failed/invalid input. Repeat the process. Read the display and refer to the user guide if
necessary.
No time is specified for a message in the call list.
• The date/time are not set. Set the date and time.
Registration or connection problems with a Bluetooth headset.
¤ Reset the Bluetooth headset (see the user guide for the headset).
¤ Delete the registration data on the handset by de-registering the device ( p. 24).
¤ Repeat the registration process ( p. 25).
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens OpenScape DECT Phone S5 on OpenScape Cordless Enterprise at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens OpenScape DECT Phone S5 on OpenScape Cordless Enterprise in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info