671508
26
Zoom out
Zoom in
Previous page
1/428
Next page
LOGO!Soft Comfort V8.2
1.8 LOGO! mit AS-Interface (0BA0-0BA2)
LOGO!Soft Comfort Online-Hilfe
26 Betriebsanleitung, 11/2017
1.8
LOGO! mit AS-Interface (0BA0-0BA2)
1.8.1
AS-Interface
Einleitung
In diesem Abschnitt erfahren Sie, was Sie beachten müssen, wenn Sie eine LOGO! mit
integriertem AS-Interface verwenden.
Konvertieren von Schaltprogrammen
LOGO!Soft Comfort konvertiert Schaltprogramme mit AS-Interface-Eingängen (Seite 27)
oder AS-Interface-Ausgängen (Seite 27), die für Vorgängerversionen der modularen LOGO!
erstellt wurden:
Wenn Sie einer LOGO! Basic ein Schaltprogramm über Extras → Geräteauswahl
(Seite 100) zuweisen
Wenn Sie ein Schaltprogramm ohne Änderungen in eine LOGO! Basic laden
Wenn Sie einen oder mehrere AS-Interface -Eingänge oder -Ausgänge eines älteren
Schaltprogramms ausschneiden und in das Schaltprogramm für eine LOGO! Basic einfügen,
wird/werden die eingefügte(n) E/A auch in das neue Schaltprogramm konvertiert.
Konvertierungsregeln
Die Eingänge Ia1 bis Ia4 werden nach I13 bis I16 konvertiert.
Die Ausgänge Qa1 bis Qa4 werden nach Q9 bis Q12 konvertiert.
Im Infofenster wird Ihnen angezeigt, welche AS-Interface -E/A auf welche Ein- oder
Ausgänge der modularen LOGO! konvertiert wurden. Stimmt die Konvertierung nicht mit
Ihrem realen Hardwareaufbau überein, so müssen Sie die Blocknummern der
entsprechenden Ein- und Ausgänge über die Blockeigenschaften anpassen.
Zusätzliche Konstanten und Verbindungsklemmen
Beachten Sie, dass bei den Gerätelinien 0BA0 bis 0BA2 keine Unterscheidung zwischen
normalen Eingängen und AS-Interface -Eingängen getroffen wird. Bei den Gerätelinien ab
0BA3 ist durch den modularen Aufbau die Blocknummer eines digitalen, analogen oder AS-
Interface -Blocks abhängig vom Steckplatz des Erweiterungsmoduls.
Eingänge für AS-Interface (Seite 27)
Es gibt bei entsprechenden LOGO! Versionen auch Eingänge der Kennzeichnung Ia, welche
für die Eingänge des AS-Interface-Bus (Seite 27) gelten.
Bei der modular aufgebauten LOGO! (ab 0BA3) gibt es keine Unterscheidung der Eingänge
hinsichtlich AS-Interface . Die Art der Eingänge legen Sie durch die gesteckten Module und
die Reihenfolge ihrer Installation fest. Daher erscheinen hier die AS-Interface-Eingänge auch
nur als I.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens LOGO Soft Comfort Online Help at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens LOGO Soft Comfort Online Help in the language / languages: German as an attachment in your email.

The manual is 12,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens LOGO Soft Comfort Online Help

Siemens LOGO Soft Comfort Online Help User Manual - English - 414 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info