671508
223
Zoom out
Zoom in
Previous page
1/414
Next page
Reference material
5.1 Constants and connectors
LOGO!Soft Comfort Online Help
Operating Instructions, 11/2017
223
Some of the input terminals of the LOGO! 0BA6 versions 12/24RC, 12/24RCo, 24/24o, 24C
and 24Co have a dual definition: they can be used as either digital inputs or analog inputs.
See the
LOGO! Manual
or product information for specific information about specific
modules. Circuit programs written for these modules for the LOGO! 0BA5 release and earlier
can run on LOGO! 0BA6 modules without modification. New circuit programs can make use
of the new input features, which provide additional fast-speed counters and analog
capability.
For help on analog block parameters, refer to information on analog value processing
(Page 312).
The block input number is not determined by the hardware structure in sy
s-
tems operating with devices of the 0BA0 to 0BA2 series.
Overview (Page 217)
This block is not available in the UDF Editor.
5.1.1.10
Analog outputs
Eight analog outputs are available, namely AQ1, AQ2, ... AQ8. You can only set an analog
value at the analog output, that is, a function with an analog output or analog flag AM.
If you connect a special function (that has an analog output) to a
real
analog output, then
note that the analog output can only process values from 0 to 1000.
You can configure the behavior of analog outputs for LOGO! 0BA5 and higher versions in
STOP mode. Analog outputs can retain their last values when LOGO! goes to STOP mode.
Alternatively, you can configure specific values to be set for AQ1 and AQ2 (AQ1 and AQ8 for
0BA8) when LOGO! goes to STOP mode.
You can also set the analog output value range. You have two choices:
Normal (0 V to 10 V or 0 mA to 20 mA)
4 mA to 20 mA
0BA0 to 0BA5:
You cannot configure the behavior of AQ1 and AQ2 on transi-
tion to S
TOP mode for LOGO! modules prior to the 0BA5 device series.
Overview (Page 217)
This block is not available in the UDF Editor.
223


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens LOGO Soft Comfort Online Help at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens LOGO Soft Comfort Online Help in the language / languages: English as an attachment in your email.

The manual is 12,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens LOGO Soft Comfort Online Help

Siemens LOGO Soft Comfort Online Help User Manual - German - 428 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info