791049
7
Zoom out
Zoom in
Previous page
1/20
Next page
Basic operation en
7
6  Basic operation
6.1 Switching on the appliance
Press ⁠.
aThe appliance starts at fan setting2.
6.2 Switching off the appliance
Press ⁠.
6.3 Selecting a fan setting
Press ⁠or ⁠.
6.4 Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
Press ⁠ repeatedly until ⁠ appears on the display.
aAfter approx. 6 minutes, the appliance automatically
switches to fan setting 3.
6.5 Switching off intensive mode
Press ⁠ until the required fan setting is reached.
6.6 Switching on the boost function
The boost function is a short-term maximum power set-
ting which can be activated in any fan setting.
Press ⁠.
aAfter approx. 20 seconds, the fan automatically
switches back to the fan setting that was previously
set.
6.7 Switching on the fan run-on, variant1
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
Press ⁠ until ⁠ appears on the display.
aThe fan run-on starts at fan setting1.
aThe appliance switches off automatically after ap-
prox. 10 minutes.
6.8 Switching on the fan run-on, variant2
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
Press ⁠
aThe fan run-on starts at fan setting1.
aThe appliance switches off automatically after ap-
prox. 10 minutes.
6.9 Switching off the fan run-on, variant 1
Press ⁠.
6.10 Switching off the fan run-on, variant 2
Press ⁠
6.11 Switching on automatic mode1
The optimum fan setting is set automatically using a
sensor.
Press ⁠.
6.12 Switching off automatic mode1
Press ⁠.
aThe ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
aAutomatic mode runs for a maximum of four hours.
6.13 Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on. If the
sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡Factory setting:5
¡Lowest setting:0
¡Highest setting:9
6.14 Setting the sensor control
Requirement:The appliance is switched off.
1. Press and hold ⁠.
aThe setting is displayed after approx. onesecond.
2. Press ⁠or ⁠ to change the setting.
3. Release ⁠ to save the setting.
6.15 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Note:The saturation indicator does not apply for non-
regenerative odour filters that are inserted downstream
of the grease filters. These odour filters must be re-
placed twice a year.
Requirements
¡After the appliance has been switched off, ⁠ ap-
pears in the display for the grease filter.
¡After the appliance has been switched off, ⁠ ap-
pears in the display for the odour filter.
Press ⁠ and ⁠.
aThe saturation indicator is reset.
6.16 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement:The appliance is switched off.
1. To set circulating-air mode (non-regenerative filter),
press and hold ⁠ and ⁠ until indicator 2 appears
on the display.
1Depending on the appliance specifications
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens LF98BIT50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens LF98BIT50 in the language / languages: English as an attachment in your email.

The manual is 8.93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens LF98BIT50

Siemens LF98BIT50 User Manual - German - 20 pages

Siemens LF98BIT50 User Manual - Dutch - 24 pages

Siemens LF98BIT50 User Manual - French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info