790200
32
Zoom out
Zoom in
Previous page
1/48
Next page
en Troubleshooting
32
Fault Cause and troubleshooting
"Sprache Deutsch"
appears in the dis-
play.
There has been a power cut.
Implement the settings for the initial configuration.
→"Carrying out the initial configuration", Page13
The operation does
not start or is inter-
rupted.
Malfunction
Call the after-sales service.
→"Customer Service", Page33
Different causes are possible.
Check any notifications that appear in the display.
→"Displaying information", Page14
Appliance does not
heat up and "Demo
mode is switched on"
appears in the dis-
play.
Device is in demo mode.
1. Briefly disconnect the appliance from the power supply by switching the circuit breaker in
the fuse box off and back on again.
2. Switch off demo mode within three minutes in the
→"Basic settings", Page24.
There has been a power cut.
Open and close the appliance door once after a power failure.
aThe appliance is checked and is ready to use.
The appliance does
not start and "Cook-
ing compartment too
hot" appears in the
display.
The cooking compartment is too hot for the selected dish or type of heating.
Allow the cooking compartment to cool down and start again.
The time is not dis-
played when the ap-
pliance is switched
off.
Basic setting has been changed.
Change the basic setting for the time display.
→"Basic settings", Page24
Appliance door can-
not be opened.
The cleaning function locks the appliance door; ⁠lights up in the display.
Allow the appliance to cool down until ⁠ goes out in the display.
The childproof lock locks the appliance door.
Use the ⁠button to deactivate the childproof lock.
→"Childproof lock", Page22
You can switch off the lock in the basic settings.
→"Basic settings", Page24
HomeConnect is not
working correctly.
Different causes are possible.
Go to www.home-connect.com.
During simple mi-
crowave operation,
the cooking compart-
ment becomes hot.
The drying function is switched on.
The interior lighting
does not work.
The LED light is defective.
Note:Do not remove the glass cover.
Call the after-sales service.
→"Customer Service", Page33
Maximum operating
time reached.
To prevent an unwanted permanent operation, the appliance automatically stops heating
after several hours if the settings are unchanged. A message appears in the display.
The point at which the maximum operating time is reached is determined by the corres-
ponding settings for an operating mode.
1. To continue operation, switch off the appliance with ⁠ first.
2. Then use ⁠ to switch on the appliance and set the required operation.
Tip:To prevent the appliance from switching off when you do not want it to, set a cooking
time.
A message with "D"
or "E" appears in the
display, e.g. D0111
or E0111.
The electronics have detected a fault.
1. Switch the appliance off and on again.
aIf the fault was a one-off, the message disappears.
2. If the message appears again, call the after-sales service. Please specify the exact error
message when calling.
→"Customer Service", Page33
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens HM678G4S6B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens HM678G4S6B in the language / languages: English as an attachment in your email.

The manual is 1.75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info