644084
15
Zoom out
Zoom in
Previous page
1/28
Next page
15
Troubleshooting
Quite often, when there is a malfunction, it is usually a small
irregularity which is easy to rectify. Before contacting the
Technical Assistance Service, try to determine the cause of the
fault using the following table.
Troubleshooting table
Error messages
When the display panel shows an error message with
, press
the
0 button. The message will disappear. The set time
function will be deleted. If the error message does not
disappear, call the Technical Assistance Service.
The following error messages can be solved by the user.
: Risk of electric shock.!
Incorrect repairs can be dangerous. Repairs may only be
carried out by qualified personnel from the Technical Support
Service.
Changing the oven bulb
If the oven light bulb is damaged it must be replaced. Special
25 W, E14, 220 V-240 V heat-resistant light bulbs (to 300 ºC
temperature) can be obtained from the Technical Support
Service or in specialist shops. Only use this type of bulb.
: Risk of electrical discharge and the resulting shock.!
Disconnect the appliance from the mains. Ensure that this is
turned off.
1. Place a dishcloth into the cold oven to avoid damage.
2. Remove the glass protection by unscrewing it to the left.
3. Replace the bulb with a similar bulb.
4. Screw the protection glass back into place.
5. Remove the dishcloth and switch the oven back on at the
mains.
Protective glass panels
Damaged protective glass panels must be replaced. Protective
glass panels cay be obtained from the Technical Assistance
Service. Please quote your appliance's product number and
production number.
Fault Possible cause Solution/advice
The oven does
not work.
The fuse has
blown.
Check the condition of the
fuse in the fuse box.
Power cut. Check that the light in the
kitchen and other house-
hold appliances are work-
ing.
0 lights up on
the display with
some zeros.
Power cut. Set the time once again.
The oven does
not heat up.
There is dust on
the contacts.
Turn the control knobs sev-
eral times in both direc-
tions.
The oven door
does not open.
The
H symbol
lights up on the
display panel.
The oven door
has been locked
by the self-
cleaning
function
x.
Wait until the oven has
cooled and the
H symbol
turns off.
The oven does
not heat up. A
small square
lights up on the
display
Ü.
The oven is in
demo mode.
Disconnect the fuse from
the fuse box and reconnect
after around 20 seconds.
Then, within approx.
2 minutes, press the
h but-
ton for approx. 4 seconds
until the square is turned
off
Ü.
The display
shows
”‰.
The appliance
has been auto-
matically turned
off.
Turn the function control
knob to the zero setting.
Error message Possible cause Solution/advice
“‹‚‚
A button has
been pressed
for too long or
has got stuck.
Press all of the buttons one
by one. Check if any button
is stuck, covered or dirty.
“‚‹‡
The door lock
has been acti-
vated with the
door open.
Press the
0 button. You
can now begin program-
ming again.
“‚‚†
The tempera-
ture inside the
oven is too
high.
The oven door is locked
and heating has stopped.
Wait until the oven has
cooled. Press the
0 but-
ton and reset the time.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens HB65AB540 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens HB65AB540 in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens HB65AB540

Siemens HB65AB540 User Manual - German - 28 pages

Siemens HB65AB540 User Manual - French - 28 pages

Siemens HB65AB540 User Manual - Portuguese, Spanish - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info