Manual Siemens HB23AT510 (page 4 of 12) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

530846

Zoom out

Zoom in

1/12

Der Berührungsschutz muss durch den Einbau gewährleistet

sein.

Anschlussleitung mit Schutzkontakt-Stecker

Das Gerät darf nur an eine vorschriftsmäßig installierte Schutz-

kontakt-Steckdose angeschlossen werden.

Wenn der Stecker nach dem Einbau nicht mehr erreichbar ist

muss installationsseitig eine allpolige Trennvorrichtung mit

einem Kontaktabstand von mind. 3 mm vorhanden sein.

Anschlussleitung ohne Schutzkontakt-Stecker

Nur ein konzessionierter Fachmann darf das Gerät anschließen.

Für ihn gelten die Bestimmungen des regionalen Elektrizitätsver-

sorgers.

In der Installation muss ein allpoliger Trennschalter mit mindes-

tens 3 mm Kontaktöffnung vorhanden sein. Phase- und Neutral-

(“Null-“) Leiter in der Anschlussdose identifizieren. Bei Falschan-

schluss kann das Gerät beschädigt werden.

Nur nach Anschlussbild anschließen. Spannung siehe Typen-

schild. Die Adern der Netzanschlussleitung entsprechend der

Farbcodierung anschließen: grün-gelb = Schutzleiter

<, blau =

(Null) Neutral-Leiter, braun = Phase (Außenleiter).

Nur GB und Australien

Nicht mit einem 13 A Stecker anschließen oder mit 13 A absi-

chern.

Nur Schweden, Finnland und Norwegen

Das Gerät kann auch mit dem beigelegten Stecker mit dem

Schutzkontakt-System angeschlossen werden. Dieser muss

nach dem Einbau zugänglich sein. Ist dies nicht der Fall, muss

installationsseitig wieder ein allpoliger Trennschalter mit mindes-

tens 3 mm Kontaktöffnung eingesetzt werden.

Gerät befestigen - Bild 5

■ Gerät ganz einschieben und mittig ausrichten.

■ Gerät festschrauben.

■ Der Spalt zwischen Arbeitsplatte und Gerät darf nicht durch

zusätzliche Leisten verschlossen werden.

Ausbau

Gerät spannungslos machen. Befestigungsschrauben lösen.

Gerät leicht anheben und ganz herausziehen.

Installation instructions

Preparing the units - Fig. 1

■ The safe operation of this appliance can only be guaranteed if

it has been installed to a professional standard in accordance

with these installation instructions. The installer is liable for

damage incurred as a result of incorrect installation.

■ Fitted units must be heat-resistant up to 90 °C, and

neighbouring unit fronts up to 70 °C.

■ Cut-out work on the units and worktop should be performed

before fitting the appliances. Remove any shavings or the

function of the electrical components may be impaired.

■ Caution during installation. Parts that are accessible during

installation may have sharp edges. Wear protective gloves to

prevent cuts

■ The power socket for the appliance must either be located in

the hatched area B or else away from the installation space.

■ A gap of 5 mm is required between the appliance and

surrounding unit fronts.

■ Secure freestanding units to the wall using a standard bracket

Appliance under the worktop - Fig. 1

There must be a ventilation cut-out made in the intermediate

floor of the surround unit.

Secure the worktop to the fitted units.

If a fitted oven is to be built in under a hob, pay attention to the

hob installation instructions.

Appliance in a tall unit  Figs 2+4

The appliance may also be installed in a tall unit.

There must be a gap between the intermediate floors and the

mounting wall of approx. 20 mm in order to provide ventilation

to the oven.

Only fit the appliance at a height where removing baking trays

does not present a problem.

Corner installation  Fig. 3

To ensure that the appliance door can be opened in the case of

corner installation, take account of dimension D. Dimension E is

dependent on the thickness of the unit front under the handle.

Connecting the appliance to the power supply

The appliance corresponds to protection class I and may only

be operated with a protective earth connection.

The appliance must be disconnected from the power supply for

all installation work.

The appliance must only be connected with the power cable

provided. Connect the power cable to the back of the appliance

(listen for the click).

A longer power cable can be obtained from the after-sales

service.

The power cable may only be replaced by a cable from the

original manufacturer, obtainable via the after-sales service.

Contact protection must be ensured by the installation.

Power cable with a plug with earthing contact

The appliance must only be connected to a properly installed

protective contact socket.

If the plug is no longer accessible following installation, an all-

pole isolating switch must be present on the installation side

with a contact gap of at least 3 mm.

Power cable without a plug with earthing contact

Only allow a licenced professional to connect the appliance. He

is subject to the regulations of the local electricity provider.

An all-pole isolating switch with at least a 3 mm contact gap

must be fitted in the installation. Identify the phase and neutral

(zero) conductor in the connection socket. Incorrect connection

may cause damage to the appliance.

only connect as per the connection diagram. See the rating

plate for the voltage. Connect the wires of the mains power

cable according to the colour coding: green/yellow = PE

conductor

<, blue = neutral conductor, brown = phase (external

conductor).

UK and Australia only

Do not connect using a 13 A plug or protect with a 13 A fuse.

Only in Sweden, Finland and Norway

The appliance can also be connected using the plug provided

which has an earthing contact system. This must still be

accessible after installation. If this is not the case, an all-pole

isolating switch must be used on the installation side with a

contact gap of at least 3 mm.

Securing the appliance  Fig. 5

■ Fully insert the appliance and centre it.

■ Screw the appliance into place.

■ The gap between the worktop and the appliance must not be

closed by additional battens.

Removal

Disconnect the appliance from the power supply. Undo the

securing screws. Raise the appliance slightly and pull it out

completely.

Notice de montage

Préparation du meuble - fig. 1

■ Uniquement une installation effectuée selon cette notice de

montage garantit une utilisation en toute sécurité. En cas de

dommages résultant d'une installation incorrecte, l'installateur

est responsable.

■ Les meubles d'encastrement doivent résister à des

températures jusqu'à 90 °C , les façades des meubles

attenants à des températures jusqu'à 70 °C.

■ Effectuer tous les travaux de découpe sur le meuble et sur le

plan de travail avant d'encastrer les appareils. Enlever les

copeaux, le fonctionnement des composants électriques peut

être compromis.

■ Attention lors de l'encastrement! Des éléments accessibles

pendant le montage peuvent posséder des arêtes vives.

Porter des gants de protection pour éviter des coupures

■ La prise de raccordement de l'appareil doit se situer dans la

zone de la surface B ou à l'extérieur de la zone

d'encastrement.

■ Une fente d'aération de 5mm est nécessaire entre l'appareil et

les façades des meubles attenants.

■ Les meubles non fixés doivent être vissés au mur avec une

équerre usuelle du commerce C.

Appareil sous le plan de travail - fig. 1

Le faux-plancher de la niche nécessite une découpe pour

l'aération.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens HB23AT510 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens HB23AT510

Siemens HB23AT510 User Manual - English - 28 pages

Siemens HB23AT510 User Manual - German - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens HB23AT510 Manual

Product: