458703
90
Zoom out
Zoom in
Previous page
1/112
Next page
88
Service Centres (Midde East)
Gigaset SL910/910A / MEA EN / A31008-M2300-A601-1-UZ19 / appendix.fm / 14.12.2011
Version 4.1, 21.11.2007
"Base connection lost - Searching for base ..." flashes on the display.
1. The handset is outside the range of the base.
¥ Move the handset closer to the base.
2. The base is not activated.
¥ Check the base power adapter (¢page 12).
3. The base's range is reduced because Eco Mode is activated.
¥ Deactivate Eco Mode (¢ page 60) or reduce the distance between the handset and
the base.
"Handset not registered to any base" flashes in the display.
The handset has not yet been registered or was de-registered due to the registration of an
additional handset (more than six DECT registrations).
¥ Register the handset again (¢page 66).
The handset does not ring.
1. The ringtone is deactivated.
¥ Activate the ringtone (¢ page 76).
2. The phone does not ring if the caller has withheld his number.
¥ Activate the ringtone for unknown calls (¢page 75).
You cannot hear a ringtone/dialling tone from the fixed line.
The phone cord supplied has not been used or has been replaced by a new cord with the
wrong pin connections.
¥ Please always use the phone cord supplied or ensure that the pin connections are correct
when purchasing from a retailer (
¢page 97).
The connection always terminates after approx. 30 seconds.
Repeater activated/deactivated (
¢page 77).
¥ Activate/deactivate the handset (¢page 21).
Error tone sounds after system PIN prompt.
You have entered the wrong system PIN.
¥ Reset the system PIN to 0000 (¢page 77).
Forgotten system PIN.
¥ Reset the system PIN to 0000 (¢page 77).
The other party cannot hear you.
The handset is "muted".
¥ Unmute the microphone (¢ page 37).
The number of the caller is not displayed although CLIP has been set.
Calling Line Identification is not enabled.
¥ The caller should ask the network provider to enable Calling Line Identification (CLI).
You hear an error tone when keying an input.
Action has failed/invalid input.
¥ Repeat the process.
Read the display and refer to the user guide if necessary.
You cannot listen to messages on the network mailbox.
Your PABX is set to pulse dialling.
¥ Set your PABX to tone dialling.
90


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens Gigaset SL910A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens Gigaset SL910A in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens Gigaset SL910A

Siemens Gigaset SL910A User Manual - German - 114 pages

Siemens Gigaset SL910A User Manual - Dutch - 113 pages

Siemens Gigaset SL910A User Manual - French - 113 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info