495131
83
Zoom out
Zoom in
Previous page
1/100
Next page
81
Service (Customer Care)
Gigaset S810-S810A / Grossbritannien / A31008-M2306-L101-1-7619 / appendix.fm / 04.08.2014
Version 4.1, 21.11.2007
Questions and answers
If you have any questions about the use of
your phone, you can contact us 24/7 at
www.gigaset.com/service
.
The table below contains a list of common
problems and possible solutions.
Registration or connection problems with a
Bluetooth headset.
¥ Reset the Bluetooth headset (see the user
guide for your headset).
¥ Delete registration data from the handset
when deregistering the device (
¢ page 68).
¥ Repeat the registration process (¢ page 68).
The display is blank.
1. The handset is not switched on.
¥ Press and hold the end call key a.
2. The battery is empty.
¥ Charge the battery or replace it
(
¢ page 14).
Not all menu items are displayed.
The menu display is restricted (standard mode).
¥ Activate extended menu display
(expert mode
) (¢ page 28).
No Base flashes on the display.
1. The handset is outside the range of the base.
¥ Move the handset closer to the base.
2. The base's range is reduced because
Eco Mode is activated.
¥ Deactivate Eco Mode (¢ page 59) or
reduce the distance between the handset
and the base.
3. The base is not switched on.
¥ Check the base power adapter
(
¢ page 12).
Please register handset flashes on the display.
Handset has not been registered with the base or
has been deregistered.
¥ Register the handset (¢ page 62).
Handset does not ring.
1. The ringtone is deactivated.
¥ Activate the ringtone (¢ page 73).
2. Call divert set for "All Calls".
¥ Deactivate call divert (¢ page 36).
3. The phone only rings if the phone number
has been transferred.
¥ Switch on the ringtone for unknown calls
(
¢ page 73).
You cannot hear a ringtone/dialling tone from
the fixed line network.
The phone cord supplied has not been used or
has been replaced by a new cord with the wrong
pin connections.
¥ Please always use the phone cord supplied or
ensure that the pin connections are correct
when purchasing from a retailer
(
¢ page 12).
The connection always terminates after
approx. 30 seconds.
Repeater activated/deactivated (
¢ page 76).
¥ Activate/deactivate the handset
(
¢ page 25).
Error tone sounds after system PIN prompt.
You have entered the wrong system PIN.
¥ Reset the system PIN to 0000 (¢ page 77).
Forgotten the system PIN.
¥ Reset the system PIN to 0000 (¢ page 77).
The other party cannot hear you.
You have pressed the mute button h. The
handset is "muted".
¥ Reactivate the microphone (¢ page 34).
The number of the caller is not displayed
despite CLIP.
Calling Line Identification is not enabled.
¥ The caller should ask the network provider to
enable Calling Line Identification (CLI).
You hear an error tone when keying an input (a
descending tone sequence).
Action has failed/invalid input.
¥ Repeat the operation.
Watch the display and refer to the user guide
if necessary.
You cannot listen to messages on the network
mailbox.
Your PABX is set for pulse dialling.
¥ Set your PABX to tone dialling.
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens Gigaset S810A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens Gigaset S810A in the language / languages: English as an attachment in your email.

The manual is 2,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens Gigaset S810A

Siemens Gigaset S810A User Manual - German - 104 pages

Siemens Gigaset S810A User Manual - Dutch - 98 pages

Siemens Gigaset S810A User Manual - French - 109 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info