300747
61
Zoom out
Zoom in
Previous page
1/80
Next page
59
Customer Service & Assistance
Gigaset E490/E495 / GBR / A31008-M2105-L101-2-7619 / appendix.fm / 15.05.2013
Version 4, 16.09.2005
Questions and answers
If you have any questions about the use
of your phone, you can contact us 24/7
at www.gigaset.com/service
. The table
below contains a list of common problems
and possible solutions.
E495 Gigaset only:
The display is blank.
1. The handset is not switched on.
¥ Press and hold the end call key a.
2. The batteries are flat.
¥ Charge or replace the batteries
(
¢page 10).
"Base x" flashes on the display.
1. The handset is outside the range of the base
station.
¥ Move the handset closer to the base sta-
tion.
The base station's range is reduced because
eco mode is activated.
¥ Deactivate eco mode (¢ page 45) or
reduce the distance between the handset
and the base station.
2. The base station is not turned on.
¥ Check the base station's mains adapter
(
¢page 8).
"Please register" flashes in the display.
Handset has not been registered with the base
station or has been deregistered.
¥ Register the handset (¢page 46).
Handset does not ring.
1. The ringer is deactivated.
¥ Activate the ringer (¢page 53).
2. Call divert set to All Calls.
¥ Deactivate call divert (¢ page 25).
You cannot hear a ringer/dialling tone from the
fixed line network.
The phone cord supplied has not been used or
has been replaced by a new cord with the wrong
pin connections.
¥ Please always use the phone cord supplied or
ensure that the pin connections are correct
when purchasing from a retailer (
¢page 8).
Error tone sounds after system PIN prompt
You have entered the wrong system PIN.
¥ Reset the system PIN to 0000 (¢page 55).
Forgotten the system PIN.
¥ Reset the system PIN to 0000 (¢page 55).
Call charges are not displayed.
1. Your network provider does not support this
feature.
2. There are no metering pulses.
¥ Ask your network provider to transmit the
metering pulses.
The other party cannot hear you.
You have pressed the
u (INT) key. The handset
is "muted".
¥ Activate the microphone again (¢page 23).
The number of the caller is not displayed
despite CLIP.
Calling Line Identification is not enabled.
¥ The caller should ask the network provider to
enable Calling Line Identification (CLI).
You hear an error tone when keying an input
(a descending tone sequence).
Action has failed/invalid input.
¥ Repeat the operation.
Watch the display and refer to the user guide if
necessary.
You cannot listen to messages on the network
mailbox.
Your PABX is set for dial pulsing.
¥ Set your PABX to tone dialling.
No time is specified for a message in the calls
list.
Date and time have not been set.
¥ Set the date/time (¢page 13).
The answering machine announces "PIN is
incorrect" during remote operation.
1. You have entered the wrong system PIN.
¥ Enter the system PIN again.
2. The system PIN is still set to 0000.
¥ Change the system PIN (¢page 55).
The answering machine is not recording any
messages/has switched over to announce only.
Its memory is full.
¥ Delete old messages.
¥ Play back new messages and delete.
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens gigaset e490 twin at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens gigaset e490 twin in the language / languages: English as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens gigaset e490 twin

Siemens gigaset e490 twin User Manual - German - 84 pages

Siemens gigaset e490 twin User Manual - Dutch - 80 pages

Siemens gigaset e490 twin User Manual - French - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info