472670
101
Zoom out
Zoom in
Previous page
1/135
Next page
99
Customer Service & Assistance
Gigaset DL500A analog / IM-NORD EN / A31008-N3103-R201-2-7619 / appendix.fm / 20.01.11
Version 4, 16.09.2005
Questions and answers
If you have any questions about the use of
your base, visit our website at
www.gigaset.com/service
for assistance 24/7. The table below contains
a list of common problems and possible
solutions.
Registration or connection problems with a
Bluetooth headset.
¥ Reset the Bluetooth headset (see the user
guide for your headset).
¥ Delete registration data from the base by
deregistering the device (
¢page 80).
¥ Repeat the registration process
(
¢page 78).
The display is blank.
1. The base is not connected to the mains power
supply.
¥ Check the mains connection
(
¢page 14).
2. The backlight is deactivated because a time
control was activated (¢page 87).
¥ Press any key on the base to temporarily
activate the display backlight.
Or:
¥ Deactivate the time control (¢page 87).
No connection between the base and handset.
1. Handset is out of the range of the base.
¥ Move the handset closer to the base.
2. Range of the base has been reduced as
Eco Mode is active.
¥ Deactivate Eco Mode (¢page 70) or
reduce the distance between the handset
and the base.
3. The handset has not been registered to the
base or was deregistered due to the registra-
tion of an additional handset (more than
six DECT registrations).
¥ Register the handset with the base
(
¢page 74).
4. The firmware is currently being updated.
¥ Please wait until the update is complete.
5. Base is not switched on.
¥ Check the power adapter for the base
(
¢page 13).
The base does not ring.
1. The ringer is switched off.
¥ Activate the ringer (¢ page 89).
2. Call divert set for "All Calls".
¥ Deactivate call divert (¢ page 32).
The display shows "Please check phone connec-
tion".
Connector to the telephone network may not be
plugged in.
¥ Check the telephone connection
(
¢page 13).
You cannot hear a ringer/dialling tone from the
fixed line.
The supplied phone cable is not being used or
the phone cable may be faulty.
¥ Replace the phone cable. When purchasing
from a phone retailer, ensure the cable has
the correct jack pin connections
(
¢page 103).
Some of the network services do not work as
specified.
Features are not activated.
£Query with the network provider.
Error tone sounds after system PIN prompt.
You have entered the wrong system PIN.
¥ Repeat input of system PIN.
The other party cannot hear you.
You have pressed the mute button P.
The base is "muted".
¥ Unmute the microphone (¢ page 30).
The number of the caller is not displayed
despite CLIP/CLI being activated.
Calling Line Identification is not enabled.
¥ The caller should ask the network provider to
enable Calling Line Identification.
You hear an error tone when keying in informa-
tion (a descending tone sequence).
Action has failed/invalid input.
¥ Repeat the process.
Watch the display and refer to the user guide
if necessary.
No time is specified for a message in the call list.
Date and time have not been set.
¥ Set date/time or
¥ Activate synchronisation with a time server
on the Internet via the Web configurator.
101


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens Gigaset DL500A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens Gigaset DL500A in the language / languages: English as an attachment in your email.

The manual is 3,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens Gigaset DL500A

Siemens Gigaset DL500A User Manual - German - 148 pages

Siemens Gigaset DL500A User Manual - Dutch - 73 pages

Siemens Gigaset DL500A User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info