Manual Siemens Gigaset DA610 (page 11 of 15) (English)

504664

Zoom out

Zoom in

1/15

Gigaset DA610 / en / A30350-M212-R102-8-UJ19 / telephony.fm / 29.03.2016

el en es it pt 11

1110-01

Network services

Public telephone systemsoffer you – in some cases only on request – a

range of helpful, additional services (e. g. call forwarding, callback when

busy, withheld number, etc.). These services can be selected using spec-

ified key combinations, of which your network provider will notify you.

Caller display (CLIP)

If the caller display service is activated, an incoming call is shown on the

display with the number and saved in the call list. Requirement: The

network provider supports the following service features and the num-

ber transfer is not withheld by the caller:

u CLI (Calling Line Identification): The caller's number is transferred.

u CLIP (Calling Line Identification Presentation): The caller's number is

displayed.

You can transfer this number to the phonebook and edit it (

£ page 7).

If you have saved the local dialling code (

£ page 11), a call with the

same dialling code is automatically only displayed as the number with-

out the dialling code.

Recall key

In public telephone systems the recall key (flash) is required for the use

of various additional services; e.g. for "callback when busy".

If necessary, the flash time on your telephone must be adjusted to the

requirements of the telephone system (

£ page 11).

Setting up a dialling code

If necessary you can change the default setting for the area code for your

connection which is saved in the telephone. The number saved here is

then used to display only the number of the person calling without the

area code in the call lists, provided they have the same area code.

You can enter two area codes.

K 4 Activate setting mode for the area code. The default num-

ber is displayed.

Q ... O / * / #

Enter the new area code (max. 5 digits).

To edit the second area code:

v Confirm with [ and continue.

To save the settings:

K Save your settings and exit the setting mode.

Note: The names of persons, whose numbers are stored in the phone-

book with the area code defined here, are no longer displayed. Change

the appropriate phonebook entries, where necessary.

Operation on a PABX

Special functions/Recall key

During an external call, you can make an enquiry or forward the call. To

do this, press the recall key

H. The subsequent procedure depends

on your PABX. To set the recall key, the telephone's flash time must be set

consistently with your PABX. Please refer to the operating instructions

for your PABX.

Changing the dialling mode/flash time

The telephone supports the following dialling modes:

u Tone dialling

u Pulse dialling

Depending on your PABX, you may need to change your phone's dialling

mode or the flash time. (Default setting: Tone dialling)

Changing the dialling mode

K # Activate setting mode for the dialling mode.

Press the key code for the dialling mode:

K Save your settings and exit the setting mode.

Temporary switch to tone dialling in "Pulse" position

To use functions that require tone dialling (e.g. remote control of

answering machine), you can set the telephone to tone dialling for the

duration of the call.

After the connection is established:

* Press the star key.

After the connection is terminated, the setting reverts to pulse dialling.

Changing the flash interval

You can change the flash interval if the dialling mode is set to tone dial-

ling (see above) (default setting 90 ms).

K  Activate setting mode.

O 5 Press the key code for setting the flash interval.

Q ... 4 Select the flash interval (ms):

K Press the set key to save your settings and exit the setting

mode.

Setting dialling prefixes

If your phone is connected to a PABX, you may have to use a dialling pre-

fix to make external calls. You can save up to three prefixes in your tele-

phone.

If a dialling prefix is recognised during dialling, a dialling pause will auto-

matically be applied. You can adjust the time of the dialling pause if nec-

essary (

£ page 12).

K Q Activate setting mode for the dialling prefix.

The current setting of the first dialling prefix is displayed.

Q ... O, *, #, H

Enter the dialling prefix (1 to 3 digits) and confirm with [.

Enter the next prefix and confirm with

u Hold down the control key X to delete the current dial-

ling prefix.

K Save your settings and exit the setting mode.



Tone dialling

Pulse dialling

0 = 90 1 = 120 2 = 270 3 = 375 4 = 600

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens Gigaset DA610 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens Gigaset DA610

Siemens Gigaset DA610 User Manual - German - 16 pages

Siemens Gigaset DA610 User Manual - French - 18 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens Gigaset DA610 Manual

Product: