298633
33
Zoom out
Zoom in
Previous page
1/41
Next page
30
Appendix
Gigaset C 455 / Irland / A31008-M1707-V101-2-7619 / appendix.fm / 11.7.07
Appendix
Symbols and typographical
conventions used
This section explains the meaning of certain
symbols and typographical conventions that
are used in this user guide.
~ Enter digits or letters.
§Menu§ The display functions currently in
the bottom display line are shown
in reversed highlights. Press the
relevant display key to launch the
function.
q Press the top or bottom of the con-
trol key, e.g. when scrolling.
c / Q / P etc.
Press the illustrated key on the
handset.
External Calls / Internal Calls (example)
Select one of the menu functions
(External Calls or Internal Calls )
from the list and press
§OK§.
§Menu§ ¢ Audio Settings ¢ Ringer Melody
(example)
Press
§Menu§. Select Audio Settings
using
q and press §OK§. Select
Ringer Melody using
q and press
§OK§.
Care
Wipe the base station, charging cradle and
handset with a damp cloth (do not use solvent)
or an antistatic cloth.
Never use a dry cloth. This can cause static.
Contact with liquid
If the handset has come into contact with liq-
uid:
1. Switch off the handset and remove the
battery pack immediately.
2. Allow the liquid to drain from the handset.
3. Pat all parts dry, then place the handset with
the battery compartment open and the key-
pad facing down in a dry, warm place for at
least 72 hours (not in a microwave, oven
etc.).
4. Do not switch on the handset again until
it is completely dry.
When it has fully dried out, you will normally be
able to use it again.
Questions and answers
If you have any questions about using your
phone, visit us anytime at
www.siemens.com/gigasetcustomercare
. The
table below contains a list of common prob-
lems and possible solutions.
!
The display is blank.
1. The handset is not switched on.
¥ Press and hold the end call key a.
2. The battery is flat.
¥ Charge the battery or replace it (page 6).
The handset does not respond to a key press.
The keypad lock is activated.
¥ Press and hold the hash key
#
(page 11).
Base is flashing in the display.
1. The handset is outside the range of the base sta-
tion.
¥ Move the handset closer to the base.
2. The base station is not switched on.
¥ Check the base station mains adapter
(page 5).
Handset does not ring.
The ringtone is switched off.
¥ Activate the ringtone (page 27).
You cannot hear a ringtone/dialling tone.
Base station's phone cord has been replaced.
¥ When purchasing a new cord, ensure that it has
the correct pin connections (page 5).
The incoming call number is not displayed
although CLIP (page 10) is set.
Phone number identification is not enabled.
¥ The caller should ask his network provider to ena-
ble Calling Line Identification (CLI).
You hear an error tone when keying an input
(a descending sequence of tones).
Action has failed/invalid input.
¥ Repeat the operation.
Watch the display and refer to the operating
instructions if necessary.
The calls list does not indicate a time for a mes-
sage.
Date/time are not set.
¥ Set the date/time (page 7).
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens gigaset c455 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens gigaset c455 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens gigaset c455

Siemens gigaset c455 User Manual - German - 41 pages

Siemens gigaset c455 User Manual - Dutch - 41 pages

Siemens gigaset c455 User Manual - French - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info